HG116FH008
24Pages

Catalog excerpts

SPECIFICATION FOR TFT LCD MODULE CUSTOMER : _ CUSTOMER MODULE :_ Customer Confirmation column: Approved by : Dept. :Data : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. HongGuang Display Co.,Ltd

Open the catalog to page 1

HongGuang Display Co.,Ltd

Open the catalog to page 2

深圳市鸿光显示有限公司 Revision History Version HongGuang Display Co.,Ltd Preliminary Specification first update Modify BLU connector pin definition

Open the catalog to page 3

深圳市鸿光显示有限公司 1. GENERAL DESCRIPTION 1.1 General Description The specification is applied to 11.6inch model (HG116FH008 ) TFT Liquid Crystal Display. The matrix uses a-Si Thin Film Transistor as a switching device. This TFTLCD has a 11.6 inch diagonally measured active display area with FHD resolution (1920 horizontal by 1080 vertical pixels array). All input signals are eDP1.2 interface compatible. HongGuang Display Co.,Ltd

Open the catalog to page 4

1.2 Features (1) 2 lane eDP interface with 2.7 Gbps link rates (2)16.7M color depth, color gamut 68% (3) Green product (RoHS & Halogen free product) (4) On board LED driving circuit (5) LED Dimming Mode DC 1.3 General Specifications The followings are general specifications. Table l.General Specifications

Open the catalog to page 5

The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. Table 2.Absolute Maximum Ratings Note (1) All the parameters specified in the table are absolute maximum rating values that may cause faulty operation or unrecoverable damage, if exceeded. Note (2) All the contents of electro-optical specifications and display fineness are guaranteed under Normal Conditions. All the display fineness should be inspected under normal conditions. Normal conditions are...

Open the catalog to page 6

深圳市鸿光显示有限公司 Relative Humidity (%RH) 80 60 Operating Range 40 20 Storage Range Temperature (º C) Figure 3. Absolute Ratings of Environmentof the LCDC) (ºModule 3. ELECTRICAL SPECIFICATIONS 3.1 Interface Connector Table 3. Signal Connector Type Item Manufacturer / Type Table 4. Signal Connector Pin Assignment SIGNAL NAME DESCRIPTION HongGuang Display Co.,Lt

Open the catalog to page 7

Note: (1) Input signals shall be low or Hi- resistance state when Vcc is off. (2) It is recommended to refer the specifications of VESA Display Port Standard. HongGuang Display Co.,Ltd HG116FH008-V1 8 / 24

Open the catalog to page 8

Figure 4. Display Port Main Link Signal Figure 5. Display Port AUX_CH Signal Table 6. Display Port AUX_CH HongGuang Display Co.,Ltd

Open the catalog to page 9

深圳市鸿光显示有限公司 Allowable Logic/LCD Drive Ripple Voltage LED Power Supply LED Driver Input Voltage PWM Signal Voltage LED Enable Voltage VPWM VLED_EN Duty Ratio Note (1)All of the specifications are guaranteed under normal conditions. Normal conditions are defined as follow: Temperature: 25℃, Humidity: 50±10%RH. Note (2) All of the absolute maximum ratings specified in the table, if exceeded, may cause faulty operation or unrecoverable damage. It is recommended to follow the typical value. Note (3) The specified VCC current and power consumption are measured under the VCC=3.3V, FV= 60Hz...

Open the catalog to page 10

3.5 Power ON/OFF Sequence Interface signals are also shown in the chart. Signalsfrom any system shall be Hi-Z state or low level when VCCvoltageis off. T11 Sink AUX CH Source Main Link Data LED EN Video from source Automatic or sink RFB Black Video Automatic Black Video link trainin idle g valid video data or PSR active Figure 5. Power Sequence HongGuang Display Co.,Ltd

Open the catalog to page 11

ii7 ible 10. Power Sequencing Requirements_ HongGuang Display Co.,Ltd HG116FH008-V1 12/ 24

Open the catalog to page 12

深圳市鸿光显示有限公司 4.OPTI CAL SPECIFICATION 4.1 The table below is the test condition of optical measurement. Table 13. Test condition of optical measurement Item Ambient Temperature Ambient Humidity Supply Voltage Driving Signal Refer to the typical value in Chapter 3: ELECTRICAL SPECIFICATIONS Vertical Refresh Rate Dark room

Open the catalog to page 13

4.2 Optical Specifications Table 14. Optical Specifications (1)The color chromaticity coordinates specified in Table 14 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. (2) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression, fD Contrast Ratio (CR): CR = CR^ CRW : Luminance of LCD module with full screen white pattern (255,255,255) at center point. CRD : Luminance of LCD module with full screen Dark pattern (0,0,0) at center point....

Open the catalog to page 14

深圳市鸿光显示有限公司 Table 15.Switching time of luminance ratios matrix To Measured Response time Figure 7. The definition of TR and TF Measured response time is determined by rise time (T R) and fall time (TF) , and shown in Figure 7. (4)Definition of Viewing angle: As CR definition is stated in Note(2), the viewing angles are defined when the viewing angle is larger than 10°in four directions relative to the perpendicular direction of the VTK’s module (two vertical angles: up θy+ and down θy-; and two horizontal angles: right θx+ and left θx-). The standard setup of measurement is shown in Figure...

Open the catalog to page 15

深圳市鸿光显示有限公司 5. MECHANICAL OUTLINE DIMENSION HongGuang Display Co.,Ltd

Open the catalog to page 16

深圳市鸿光显示有限公司 7. RELIABILITY TEST The reliability test items and its conditions are shown in below. Table 17.Reliability Test No Test Items High temperature storage test Low temperature storage test High temperature & high humidity operation test 55 ℃, 90%RH, 300hrs High temperature operation test Low temperature operation test Thermal shock Vibration Test

Open the catalog to page 21

10. GENERAL PRECAUTION 10.1 Using Restriction This product is not authorized for using in life supporting systems, aircraft navigation control systems, military systems and any other appliance where performance failure could be life-threatening or lead to be catastrophic. 10.2 Operation Precaution (1)The LCD product should be operated under normal conditions. Normal conditions are defined as below: Temperature: 25℃ Humidity: 50± 10% Display pattern: continually changing pattern (Not stationary) (2) Brightness and response time depend on the temperature. (It needs more time to reach normal...

Open the catalog to page 22