HG104SV003
27Pages

Catalog excerpts

SPECIFICATION FOR TFT LCD MODULECUSTOMER:CUSTOMER MODULE :_ HL MODEL : HG104SV003 □Preliminary Specification ■Final Specification Customer Confirmation column: Approved by :Dept. :Data : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document.

Open the catalog to page 1

REVISION HISTORY Version

Open the catalog to page 2

深圳市鸿光显示有限公司 1.0 GENERAL DESCRIPTION 1.1 Introduction HG104SV003 is a color active matrix TFT LCD module using amorphous silicon TFT‘s (Thin Film Transistors) as an active switching devices. This module has a 10. 4 inch diagonally measured active area with SVGA resolutions (800 horizontal by 600 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. LVDS Signal Signal Input Connector DC/DC Converter DDIC VLED BLU Input Connector 1.2 Features  0.5T Glass（Single）  Reverse Type  6bit+2bit FRC...

Open the catalog to page 4

1.3 Application • Medical & Industrial application 1.4 General Specification The followings are general specifications at the HG104SV003 <Table 1. LCD Module Specifications>

Open the catalog to page 5

Operating Temperature Storage Temperature Note : 1) Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 ℃ max. and no condensation of water. HongGuang Displa

Open the catalog to page 6

3.0 INPUT TERMINAL PIN ASSIGNMENT This LCD employs two interface connections, a 20 pin connector is used for the LCD module electronics interface and a 2 pin connector is used for the backlight system. 3.1 Pin assignment for LCD module Connector: MSB24013P20 _HA(STM) or equivalent < Table5. Pin Assignment for LCD Module Connector >

Open the catalog to page 7

深圳市鸿光显示有限公司 3.2 Pin assignment for LED Bar Connector : JST BHSR-02VS-1 or equivalent < Table6. Pin assignment for LED Bar > Pin No Power supply Power supply

Open the catalog to page 8

深圳市鸿光显示有限公司 3.3 Input Color Data Mapping < Table11. Input Signal and Display Color Table > Input Data Signal Color & Gray Scale Basic Colors Gray Scale of Green Gray Scale of Blue Gray Scale of White Black Blue Green Cyan Red Magenta Yellow White Black △ Darker △ ▽ Brighter ▽ Red Black △ Darker △ ▽ Brighter ▽ Green Black △ Darker △ ▽ Brighter ▽ Blue Black △ Darker △ ▽ Brighter ▽ White Green Data Blue Data

Open the catalog to page 9

深圳市鸿光显示有限公司 3.4 Input Color Data Mapping Display Position of Input Data (V-H)

Open the catalog to page 10

< Table 3. LCD Module Electrical specifications > Parameter Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VBAT=3.8V, Frame rate fV=60Hz and Clock frequency = 1 56.8MHz. Test Pattern of power supply current a) Typ : Mosaic 8x6 Pattern(L0/L255) b) Max : skip subPixel(L255) 2. The duration of rush current is about 2ms and rising time of Power Input is 1 ms(min)

Open the catalog to page 11

深圳市鸿光显示有限公司 5.1 AC Specification LVCLKP LVCLKN LV0P/N ~ LV3P/N TBIT=1/(F*7)(1) LV3P/N Note: (1) TBIT: Data period (2) Internal CLK sampling data window < LVDS channel to channel skew> Description LVDS Input frequency LVDS channel to channel skew

Open the catalog to page 13

深圳市鸿光显示有限公司 5.2 Interface timing Parameter < Table9. Timing Parameter > Item Horizontal Active time Horizontal Back Porch Horizontal Front Porch Vertical total time Vertical Active time Vertical Back Porch Vertical Front Porch Horizontal total time Pixels Rate Frame Rate

Open the catalog to page 14

深圳市鸿光显示有限公司 5.3 Power Sequence [Ta =25±2 ℃] 90% Tcon Reset Interface Signal (LVDS/MIPI/eDP) Valid video < Table10. Sequence Table > Value

Open the catalog to page 15

6.0 Back-Light Unit Table 4. LED Bar Electrical Specifications > [Ta =25±2 c] Parameter Pled = VLED xILED(Without LED converter transfer efficiency) 2. The life time of LED, 30,000Hrs, is determined as the time at which luminance of the LED is 50% compared to that of initial value at the typical LED current on condition of continuous operating at 25 ± 2°C. 3. Only under the above operating conditions could the life time of LED be guaranteed.

Open the catalog to page 16

7.0 OPTICAL SPECIFICATIONS 7.1 Overview The test of optical specifications shall be measured in a dark room (ambient luminance < 1 lux and temperature = 25±2°C) with the equipment of Luminance meter system (Gonio meter system and TOPCON BM-5) and test unit shall be located at an approximate dista nce 50cm from the LCD surface at a viewing angle of 0 and O equal to 0°. We refer to 00 =0 (=03 ) as the 3 o' clock direction (the "right" ), 00=90 (= 012 ) as the 12 O' clock direction ( "upward" ), 00=180 (= 09 ) as the 9 O' clock direction ( "left" ) and 00=27 0(= 06 ) as the 6 O' clock...

Open the catalog to page 17

深圳市鸿光显示有限公司 Note1:Luminance measurement The test condition is at ILED=100mA and measured on the surface of LCD module at 25℃.  The data are measured after LEDs are lighted on for more than 5 minutes and LCM displays are fully white. The brightness is the center of the LCD. Measurement equipment CS2000 or similar equipments (Field of view:1deg,Distance:50cm)  Measuring surroundings: Dark room.  Measuring temperature: Ta=25℃.  Adjust operating voltage to get optimum contrast at the center of the display.  Measured value at the center point of LCD panel must be after more than 5 minutes...

Open the catalog to page 18

tv Note 3:The definition of Viewing Angle Refer to the graph below marked by 0 and O. Note4:ThedefinitionofContrastRatio (Test LCM using CS2000 or similar equipments): Luminance When LCD is at "White" state Contrast Ratio(CR)= - Luminance When LCD is at "Black" state (Contrast Ratio is measured in optimum common electrode voltage) Note5:DefinitionofResponse time.(Test LCD using DMS501 or similar equipments): The output sign also photo detector are measured when the input sign also are changed from "black " to "white" (Voltage falling time)and from "white" to "black" (Voltage rising time),...

Open the catalog to page 19

深圳市鸿光显示有限公司 Note 6: Color Coordinates of CIE 1931 The test condition is at ILED=100mA and measured on the surface of LCD module at 25℃. Measurement equipment:CS2000 or similar equipments The Color Coordinate (CIE 1931) is the measurement of the center of the display shown in below figure. Note 7: Definition of Color of CIE Coordinate and NTSC Ratio. Note 8: Polarization Direction Definition  Viewing direction is normal user viewing direction which is vertical to the display surface  The polarizer which is closer to viewer is defined as Front Polarizer  The polarizer which is on the rear...

Open the catalog to page 20