HG101WX053
12Pages

Catalog excerpts

SPECIFICATION FOR TFT LCD MODULE CUSTOMER: _ CUSTOMER MODULE :_ □ Preliminary Specification ■ Final Specification Customer Confirmation column: Approved by :Dept. :Data : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document.

Open the catalog to page 1

深圳市鸿光显示有限公司 REVISION STATUS Version Revise Date First Issued.

Open the catalog to page 2

深圳市鸿光显示有限公司 TABLE OF CONTENTS NO.

Open the catalog to page 3

1. General Description 1.1 Description HG101WX053 is a color active matrix thin film transistor (TFT) IPS liquid crystal display(LCD) that uses amorphous silicon TFT as a switching device. It is composed of a TFT LCD panel,DriverIC, FPC and Backlight, This TFT LCD has a 10.1-inch diagonally measured active display area with WSVGA resolution (800 vertical by 1280 horizontal pixel array).

Open the catalog to page 4

深圳市鸿光显示有限公司 2. MECHANICAL SPECIFICATION

Open the catalog to page 5

MIPI differential data input MIPI differential data input MIPI differential data input MIPI differential data input MIPI differential clock input MIPI differential clock input MIPI differential data input MIPI differential data input MIPI differential data input MIPI differential data input Global reset pin，Active low

Open the catalog to page 6

4. Electrical Characteristics4.1 TFT LCD Module Parameter 4.2Power ON/OFF Sequence To prevent the device damage from latch up, the power on/off sequence shown below must be followed. Power on: VDD, GND - AVDD, AGND - V1 to V14 Power off: V1 to V14 - AVDD, AGND- VDD, GND

Open the catalog to page 7

v:d iTE-'E nn k I vavHL-/-.nr-H.'-.rin .'jChlh WS. VHr-vryv.i". 3 HIK4 :i:I ii nvc Power off timing sequence Note: Low level=3FH, when NBW=L (Normally white) Low level=00H, when NBW=H (Normally black 4.3 Back Light Unit

Open the catalog to page 8

Notel: Measurement Setup The LCD module should be stabilized at given temperature for 15 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting backlight for 15 minutes in a windless room.

Open the catalog to page 9

Note3:Definition of Contrast Ratio (CR) The contrast ratio can be calculated by the following expression Contrast Ratio (CR) = L63 / L0 L63: Luminance of gray level 63, L0: Luminance of gray level 0 Note4:Definition of Response Time (TR, TF) Note5:Definition of Luminance White Measure the luminance of gray level 63 at center point and 5 points. Center of Luminance = Y1 Note6: Definition of Luminance Uniformity(Variation) Measure the luminance of gray level 63 at 13 points. Min Lurulnante cT , \ - ti 3 Urfflormfty oF13 points- » - sc 10Q-'Wi

Open the catalog to page 10

深圳市鸿光显示有限公司 7. GENERAL PRECAUTION 7.1 SAFETY 1. Do not swallow any liquid crystal, even if there is no proof that liquid crystal ispoisonous. 2. If the LCD panel breaks, be careful not to get liquid crystal to touch your skin. 3. If skin is exposed to liquid crystal, wash the area thoroughly with alcohol or soap. 1. Store the panel or module in a dark place where the temperature is 23±5°C and The humidity is below 50±20%RH. 2. Store in anti-static electricity container. 3. Store in clean environment, free from dust, active gas, and solvent. 4. Do not place the module near organics solvents...

Open the catalog to page 12