Shenzhen Hongguang Display Co.,Ltd CUSTOMER : CUSTOMER MODULE : HL MODEL  Preliminary Specification ■Final Specification Customer Confirmation column： Approved by : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. Hongguang Display

Shenzhen Hongguang Display Co.,Ltd REVISION STATUS Version Revise Date Hongguang Display First Issued.

Shenzhen Hongguang Display Co.,Ltd T ABLE OF CONTENTS NO. Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 1. GENERAL DESCRIPTION 1. 1 DESCRIPTION This LCM is a color active matrix thin film transistor (TFT) IPS liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. It is composed of a TFT LCD panel, Driver IC,FPC and Backlight, This TFT LCD has a 10.1-inch diagonally measured active display area with WXVGA resolution (800 horizontal by 1280vertical pixel array). Panel Size Active Area Pixel Pitch Outline Dimension Display Mode Transmission mode, normally black Viewing Direction Full viewing Display Format Surface Treatment Anti Glare...

Hongguang Display Full viewing Peeling tape UNMARKED TOLERANCE symbol NC VCC-LCD3V3 VCC-LCD3V3 NC RESET NC GND MIPI_D2N MIPI_D2P GND MIPI_D1N MIPI_D1P GND MIPI_CKN MIPI_CKP GND MIPI_D0N MIPI_D0P GND MIPI_D3N MIPI_D3P GND NC NC GND NC NC NC NC GND VLEDVLEDNC NC NC NC NC NC VLED+ VLED+ Module (down side of module surface) POWER IC烧录 Component area Black tape Yellow insulation MODULE CENTER ACTIVE AREA CENTER

Shenzhen Hongguang Display Co.,Ltd 3. PIN DESCRIPTION FPC Connector FPC is used for the module electronics interface. No. power Voltage for digital circuit power Voltage for digital circuit Negative MIPI differential data input Positive MIPI differential data input Negative MIPI differential data input Positive MIPI differential data input Negative MIPI differential clock input Positive MIPI differential clock input Negative MIPI differential data input Positive MIPI differential data input Negative MIPI differential data input Positive MIPI differential data input Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 33 Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 4. ELECTRICAL CHARACTERISTICS 4. 1 ABSOLUTE MAXIMUM RATINGS Item Digital Supply Voltage 4. 2 TFT LCD MODULE 4. 2. 1 OPERATING CONDITIONS Parameter Digital Power Supply Voltage 4. 3 CURRENT CONSUMPTION Item Digital Current LCM Power Consumption 4. 4 BACK LIGHT UNIT Ta=25℃ Item Forward voltage

Shenzhen Hongguang Display Co.,Ltd 4. 5POWER ON/ OFF SEQUENCE In order to prevent IC from power on reset fail, the rising time (TPOR) of the digital power supply VDD should be maintained within the given specifications. POWER ON/ OFF: Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 5. INPUT SIGNAL T IMING 5. 1 DC Characteristics for DSI LP Mode Hongguang Display

Shenzhen Hongguang Display Co.,Ltd Notes: 1. Ta = -30℃ to 70℃ (to +85℃ no damage) , VCI = 2.5V to 6.0V, VDDI = 1.65V to 3.3V 2. Includes 50mV (-50mV to 50mV) ground difference 3. Without VCMRCLKM450/VCMRDATAM450 4. Without 50mV (-50mV to 50mV) ground difference 5. n = 0 and 1 6. For higher bit rates, a 14pF capacitor will be needed to meet the common-mode return loss specification. 5. 2AC CHARACTERISTICS High Speed Mode – Clock Channel Timing Hongguang Display

Shenzhen Hongguang Display Co.,Ltd HIGH SPEED MODE DATA CLOCK CHANNEL TIMING Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 5. 3 PARALLEL RGB INPUT TIMING TABLE 5. 3. 1 HORIZONTAL VERTICAL T IMING Parameter Horizontal Display Area DCLK frequency HS pulse width Hs Back Porch(Blanking) Hs Front Porch Symbol thd fclk thpw thd thfp Unit DCLK MHz DCLK DCLK DCLK Vertical Timing Parameter Vertical Display Area VS Pulse Width VS Back Porch(Blanking) VS Front Porch Hongguang Display Symbol tvd tvpw tvb tvfp

Shenzhen Hongguang Display Co.,Ltd 6. OPTICAL CHARACTERISTICS Ta=25±2℃ Item Contrast Ratio Luminance uniformity Response Time 85 85 Viewing Angle degree K=Contrast Ratio>10 85 Vertical 85 0.610 Red 0.370 0.320 Green Color Chromaticity Typ- 0.590 Typ+ (CIE1931) 0.05 0.180 0.05 Blue 0.120 0.310 White 0.330 Colorgamut(NTSC ratio) 53 % Note1: Definition of optical measurement system (BM-7) Horizontal Photo detector Normal line θ=Φ=0° 12 o'clock direction Φ T =90° 500mm Active Area LCD Panel 6 o'clock direction Φ B =90° Note2: Definition of viewing angle range and measurement system Viewing angle...

Shenzhen Hongguang Display Co.,Ltd Note3: Definition of Response time The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector outputintensity changed from 90% to 10%. And fall time (TOFF) is the time between photodetector output intensity changed from 10% to 90%. Photo detector output (Relative value) Fig. 6-3 Definition of response time Note4: Definition of contrast ratio Contrast ratio(CR)= “White state “: The state is that the LCD should drive by Vwhite. “Black state”: The state is that...

Shenzhen Hongguang Display Co.,Ltd 7. RELIABILITY T EST ITEMS 7. 1 T EMPERATURE AND HUMIDITY Test Item Test Condition High Temperature Operation HighTemperatureHighHumidity Ta=60℃，90%RH， Operation 72Hrs(no condensation) Thermal Shock Image Sticking Note1:Condition of image sticking test :25℃±2℃ Operation with test pattern sustained for 1hrs,then change to 50% gray pattern immediately. after 5 mins, the mura must be disappeared completely 7. 2 VIBRATION & SHOCK Test item Packing Shock (non-operation) 980m/s2,6ms, ±x,y,z 3times for direction Frequency range:10 HZ~50HZ Stroke:1.0mm,sweep:10 HZ ~50HZ...

Shenzhen Hongguang Display Co.,Ltd 8. GENERAL PRECAUTION 8. 1 SAFETY 1. Do not swallow any liquid crystal, even if there is no proof that liquid crystal ispoisonous. 2. If the LCD panel breaks, be careful not to get liquid crystal to touch your skin. 3. If skin is exposed to liquid crystal, wash the area thoroughly with alcohol or soap. 8. 2 STORAGE CONDITIONS 1. Store the panel or module in a dark place where the temperature is 23±5°C andThehumidity is below 50±20%RH. 2. Store in anti-static electricity container. 3. Store in clean environment, free from dust, active gas, and solvent. 4. Do...