HG101WX046
18Pages

Catalog excerpts

SPECIFICATION FOR TFT LCD MODULECUSTOMER:CUSTOMER MODULE :_ HL MODEL : HG101WX046 □Preliminary Specification ■Final Specification Customer Confirmation column: Approved by :Dept. :Data : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document.

Open the catalog to page 1

深圳市鸿光显示有限公司 REVISION STATUS Version Revise Date First Issued.

Open the catalog to page 2

深圳市鸿光显示有限公司 T ABLE OF CONTENTS NO.

Open the catalog to page 3

1. General Description 1.1 Description This LCM is a color active matrix thin film transistor (TFT) IPS liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. It is composed of a TFT LCD panel, Driver IC,FPC and Backlight, This TFT LCD has a 10.1-inch diagonally measured active display area with WXVGA resolution (800 horizontal by 1280vertical pixel array).

Open the catalog to page 4

Full viewing Peeling tape UNMARKED TOLERANCE symbol NC VCC-LCD3V3 VCC-LCD3V3 NC RESET NC GND MIPI_D2N MIPI_D2P GND MIPI_D1N MIPI_D1P GND MIPI_CKN MIPI_CKP GND MIPI_D0N MIPI_D0P GND MIPI_D3N MIPI_D3P GND NC NC GND NC NC NC NC GND VLEDVLEDNC NC NC NC NC NC VLED+ VLED+ Module (down side of module surface) POWER IC烧录 Component area Black tape Yellow insulation MODULE CENTER ACTIVE AREA CENTER

Open the catalog to page 5

3. Pin Description FPC Connector FPC is used for the module electronics interface.

Open the catalog to page 6

4. Electrical Characteristics 4.1 Absolute Maximum Ratings ^l.Internal Circuit Diagram

Open the catalog to page 8

深圳市鸿光显示有限公司 4. 5POWER ON/ OFF SEQUENCE In order to prevent IC from power on reset fail, the rising time (TPOR) of the digital power supply VDD should be maintained within the given specifications. POWER ON/ OFF:

Open the catalog to page 9

5. Input Signal Timing 5.1 DC Characteristics for DSI LP Mode DC levels of the LP-00, LP-01, LP-10 and LP-11 are defined in the table below: DC Characteristics for the DSI LP mode when LP-RX, LP-CD or LP-TX is mentioned in the condition column. Other logical levels in the table are for MCU interface. Notes: 1. Ta = -30 C to 70 °C (to +85 °C no damage) 2. DSI High Speed mode is off.

Open the catalog to page 10

深圳市鸿光显示有限公司 Notes: 1. Ta = -30℃ to 70℃ (to +85℃ no damage) , VCI = 2.5V to 6.0V, VDDI = 1.65V to 3.3V 2. Includes 50mV (-50mV to 50mV) ground difference 3. Without VCMRCLKM450/VCMRDATAM450 4. Without 50mV (-50mV to 50mV) ground difference 5. n = 0 and 1 6. For higher bit rates, a 14pF capacitor will be needed to meet the common-mode return loss specification. 5. 2AC CHARACTERISTICS High Speed Mode – Clock Channel Timing HongGuang Displ

Open the catalog to page 11

High Speed Mode Data Clock Channel Timing Figure 118: DSI Data to Clock Channel Timings Table 40: DSI Data to Clock Channel Timings

Open the catalog to page 12

深圳市鸿光显示有限公司 5. 3 PARALLEL RGB INPUT TIMING TABLE 5. 3. 1 HORIZONTAL VERTICAL T IMING Parameter Horizontal Display Area DCLK frequency HS pulse width Hs Back Porch(Blanking) Hs Front Porch Symbol thd fclk thpw thd thfp Unit DCLK MHz DCLK DCLK DCLK Vertical Timing Parameter Vertical Display Area VS Pulse Width VS Back Porch(Blanking) VS Front Porch Symbol tvd tvpw tvb tvfp

Open the catalog to page 13

深圳市鸿光显示有限公司 6. OPTICAL CHARACTERISTICS Ta=25±2℃ Item Contrast Ratio Luminance uniformity Response Time 85 85 Viewing Angle degree K=Contrast Ratio>10 85 Vertical 85 0.610 Red 0.370 0.320 Green Color Chromaticity Typ- 0.590 Typ+ (CIE1931) 0.05 0.180 0.05 Blue 0.120 0.310 White 0.330 Colorgamut(NTSC ratio) 53 % Note1: Definition of optical measurement system (BM-7) Horizontal Photo detector Normal line θ=Φ=0° 12 o'clock direction Φ T =90° 500mm Active Area LCD Panel 6 o'clock direction Φ B =90° Note2: Definition of viewing angle range and measurement system Viewing angle is measured at the...

Open the catalog to page 14

Note3: Definition of Response time The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector outputintensity changed from 90% to 10%. And fall time (TOFF) is the time between photodetector output intensity changed from 10% to 90%. Contrast ratio(CR)= Luminance measured when LCD on the Whitestate Luminance measured when LCD on the Blackstate “White state “: The state is that the LCD should drive by Vwhite. “Black state”: The state is that the LCD should drive by Vblack. Vwhite: To be...

Open the catalog to page 15

7. Reliability Test Items Test item Note: Measure point : 1. LCD glass and metal bezel 2. IF connector pins

Open the catalog to page 16

深圳市鸿光显示有限公司 8. GENERAL PRECAUTION 8. 1 SAFETY 1. Do not swallow any liquid crystal, even if there is no proof that liquid crystal ispoisonous. 2. If the LCD panel breaks, be careful not to get liquid crystal to touch your skin. 3. If skin is exposed to liquid crystal, wash the area thoroughly with alcohol or soap. 8. 2 STORAGE CONDITIONS 1. Store the panel or module in a dark place where the temperature is 23±5°C andThehumidity is below 50±20%RH. 2. Store in anti-static electricity container. 3. Store in clean environment, free from dust, active gas, and solvent. 4. Do not place the module...

Open the catalog to page 17