Shenzhen Hongguang Display Co.,Ltd CUSTOMER : CUSTOMER MODULE : HL MODEL  Preliminary Specification ■Final Specification Customer Confirmation column： Approved by : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document.

Shenzhen Hongguang Display Co.,Ltd General Description Absolute Maximum Ratings Electrical Specifications Optical Specifications Interface Connection Signal Timing Specification Input Signals, Display Colors & Gray Scale of Colors Power Sequence Mechanical Characteristics Reliability Test Handling & Cautions Packing Information Mechanical Outline Dimension General Precautions

Shenzhen Hongguang Display Co.,Ltd 1.0 GENERAL DESCRIPTION 1.1 Introduction HG101WU076 is a color active matrix TFT LCD module using LTPS TFT's (Thin Film Transistors) as an active switching devices. This module has a 10.1 inch diagonally measured active area with WUX GA resolutions (1200 )horizontal by 1920 .vertical pixel array . Each pixel is divided into RED, GREE N, BLUE dots which are arranged in vertical stripe and this module can display 8bit colors and color ga mut typ. 64% @ C Light.. The LED driver for back-light driving is built in this model. All input signals are LVDS interface...

Shenzhen Hongguang Display Co.,Ltd 1.3 Application l Photographic equipment applications 1.4 General Specification The followings are general specifications at the model HG101WU076 . (listed in Table 1) Active area Pixel pitch Pixel arrangement Display colors Color gamut Display mode Normally Black Dimensional outline Surface treatment Surface hardness Bottom edge side, 1-LED lighting bar type Notes : 1. LED Lighting Bar (60*LED Array)

Shenzhen Hongguang Display Co.,Ltd 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. Absolute Maximum Ratings> Parameter Operating Temperature Storage Temperature Ta=25+/2°C Remarks Note 1 Note 2 Notes : 1. Permanent damage to the device may occur if maximum values are exceeded functional operation should be restricted to the condition described under normal operating conditions. 2. Temperature and relative humidity...

Shenzhen Hongguang Display Co.,Ltd 3.0 ELECTRICAL SPECIFICATIONS 3.1 Electrical Specifications < Table 3. Electrical Specifications > Power Supply Voltage Power Supply Inrush Current Permissible Input Ripple Voltage Power Supply Current Power Consumption High Level Differential Input Thr eshold Voltage Low Level Differential Input Thr eshold Voltage Differential input voltage Differential input common mode voltage Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VDD = 3.3V, Frame rate = 60Hz at 25...

Shenzhen Hongguang Display Co.,Ltd 3.2 Backlight Unit < Table 4. LED Driving Guideline Specifications > Parameter Power supply voltage for L ED Driver Power supply Current for B ack light Power supply Current for B ack light 1.Note 1 2.LED Power Consu mption follow custo merrequirements EN logic high vo ltage Power supply for Back light PWM Control Frequency Duty Ratio Notes : 1. Calculator Value for reference IBLU × VBLU = PBL_PWR*85% 2. The LED Life-time define as the estimated time to 50% degradation of initial luminous under the condition of the ambient temperature of 25℃.

Shenzhen Hongguang Display Co.,Ltd 4.0 OPTICAL SPECIFICATION 4.1 Overview The test of optical specifications shall be measured in a dark room (ambient luminance  1 lux and temperature = 252℃) with the equipment of luminance meter system (SR-3AR) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”)....

Shenzhen Hongguang Display Co.,Ltd Notes : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface (see Figure 7). CR = Luminance when displaying a white raster Luminance when displaying a black raster 2. Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white,...

Shenzhen Hongguang Display Co.,Ltd 4.3 Optical Measurements TFT-LCD module Optical characteristics measurement setup Figure 7. Measurement Set Up Display data Black(TFT OFF) Luminance Figure 8. Response Time Testing The electro-optical response time measurements shall be made as shown in Figure 10 by switching the “data” input signal ON and OFF. Tr: The luminance to change from 10% to 90% ,Tf: The luminance t o change from 90% to 10% . The test system : SR-3AR

Shenzhen Hongguang Display Co.,Ltd V/8 Figure 9. Cross Talk Modulation Test Description YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location 1/2/3/4 measured will be exactly the same in both patterns. The test background gray is from L64 to L192.Take the largest data as the result. Cross Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of tha t same area when any adjacent area is driven dark.(Refer...