Shenzhen Hongguang Display Co.,Ltd CUSTOMER : CUSTOMER MODULE : Preliminary Specification ■Final Specification Customer Confirmation column： Approved by : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. Hongguang Display .

Shenzhen Hongguang Display Co.,Ltd Revision History Version NO. Hongguang Display . FIRST ISSUE

Shenzhen Hongguang Display Co.,Ltd CONTENTS GENERAL INFORMATION I/O CONNECTION & BLOCK DIAGRAM ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS ELECTRO-OPTICAL CHARACTERISTICS RELIABILITY TEST CONDITIONS INSPECTION STANDARDS PACKAGE DRAWING Hongguang Display .

Shenzhen Hongguang Display Co.,Ltd 1. GENERAL INFORMATION 1.1 1) Structure: TFT PANNEL+IC+FPC+BL 2) IPS Type LCD 1920 dot-segment and 1200 dot-common outputs 3) 16.7M Color can be selected by software 4) White LED back light 5) MIPI interface 6) Operation Temperature : -20~70℃ 7) Storage Temperature : -30~80℃ 8) CTP cover lens ：Asahi 9) CTP structure ：G+G 10) LED life time：-/ 1.2 General specification Item of Panel Size Display mode Normally Black Pixel arrangement Active Area Recommended Viewing Direction Hongguang Display .

Shenzhen Hongguang Display Co.,Ltd 2.DIAGRAM FOR LCM Hongguang Display .

Shenzhen Hongguang Display Co.,Ltd 3. I/O CONNECTION Connector : FH34SRJ-34S-0.5SH(50) (HRS) or equivalent LCM Pin NO. LED POWER SUPPLY OTP_SDA OTP_SCL H,BIST; L NORMAL mode; ID Pin(1.8V ) 1.8V ( ) Power Ground Power Ground Power Ground DSI-D3- differential data signals for MIPI interface TDP3 GND TDN0 TDP0 GND TCN TCP GND TDN1 TDP1 GND TDN2 TDP2 GND STBYB SCL SDA LED_PWM Bridge_EN VDD-OTP VDD DSI-D3+ differential data signals for MIPI interface Power Ground DSI-D0- differential data signals for MIPI interface DSI-D0+ differential data signals for MIPI interface Power Ground DSI-CLK- differential...

Shenzhen Hongguang Display Co.,Ltd 4. ABSOLUTE MAXIMUM RATINGS (GND=AGND=0V) Parameter of absolute maximum ratings 参数 Operating temperature Storage temperature Note: 1. These range above is maximum value not the actual operating temperature . Actual Operating temperature is no more than 40℃ and temperature refers to the LCM surface temperature ; 2.BOE is not responsible for product problems beyond the use conditions. 5. ELECTRICAL CHARACTERISTICS 5.1 TFT LCD Module LCD Module Electrical specifications Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. Hongguang...

Shenzhen Hongguang Display Co.,Ltd The current draw and power consumption specified is for VDD=3.3V, Frame rate f V =60Hz and Clock frequency = 490MHz. Test Pattern of power supply current a) Typ : Mosaic 8 x 6 Pattern(L0/L255) b) Max : skip subPixel(L255) 2. The duration of rush current is about 2ms and rising time of Power Input is 1ms(min) 5.2 Back-light Unit LED Driving guideline specifications Notes : 1. Power supply voltage24V for LED Driver Calculator Value for reference IF × VF ×48 / 85%(efficiency) = PLED 2. The LED Life-time define as the estimated time to 50% degradation of initial...

Shenzhen Hongguang Display Co.,Ltd MIPI Timing Parameter Hongguang Display .

Shenzhen Hongguang Display Co.,Ltd Hongguang Display .

Shenzhen Hongguang Display Co.,Ltd 5.5 Power Sequence 注：1）CSR registers, PLL_EN,SOFT_RESET 都是寄存器，上电时需要通过 I2C 配置。 Data 的状态由处理器进行控制。 2）Sequence 9,10,11，这些是 IC 监测到错误后重新启动时的

Shenzhen Hongguang Display Co.,Ltd 6. ELECTRO-OPTICAL CHARACTERISTICS Parameter Contrast Ratio (Center point) Luminance uniformity Response Time WX White WY RX Red Color Chromaticity (CIE 1931) 0.30 θ = 0. Normal viewing angle B/L On Hongguang Display .

Shenzhen Hongguang Display Co.,Ltd Note1 Definition of Contrast Ratio (CR): Note2: Definition of Luminance Uniformity: Active area is divided into 9 measuring areas (Shown in below), every measuring point is placed at the center of each measuring area. FPC The spot locations for luminance measurement Bmax: Bmax: The measured maximum luminance of all measurement position. Bmin: The measured minimum luminance of all measurement position. Note 3:Definition of Response time: Sum of Tr and Tf Display data Optical Response Hongguang Display .

Shenzhen Hongguang Display Co.,Ltd Note4.Definition of Viewing Angle: The viewing angle range that the CR≥10 Note 5: Definition of Color Chromaticity (CIE 1931) Color coordinate of white & red, green, blue at center point. Hongguang Display .

Shenzhen Hongguang Display Co.,Ltd 7. RELIABILITY TEST CONDITIONS No Test Item Test Condition STANDARD 1. Functional test is OK. Missing Segment, short, unclear segment, on-display, display abnormally and liquid crystal leak are un-allowed. 2. No low temperature bubbles, end seal loose and fall, frame rainbow. High Temperature Storage High Temperature Operating Thermal and cold shock Operate at High Temperature and Humidity Vibration Test Dropping test 0°C +50°C x 10cycles (30min) (5min) (30min) 60°C x 90%RH / 24H Frequency: 10Hz~55Hz~10Hz Amplitude:1.5mm, 2 hours for each direction of X, Y,...

Shenzhen Hongguang Display Co.,Ltd 8. INSPECTION STANDARDS 8.1 AQL Sampling inspection standard 使用 GB/T 2828-2003 一般 II 水平,采用正常检查一次抽样方式；具体抽检方式参照《成品检验管 理程序》、《抽样管理规范》 缺陷区分 AQL 允收水准 严重缺陷 0收1退 重缺 0.4 轻缺 1.0

Shenzhen Hongguang Display Co.,Ltd 中尺寸点、线判定标准：（6.2 8 寸以内） 点状缺 陷 （磨伤、 异物、针 1 孔、凹痕、 缺膜、气 泡，白点、 彩点、脏 点） 判定（D 同背面丝印油墨区杂质 区） 判定标准 注：1) D 区的点状缺陷需在不影响 CTP 功能、客户组装及整机的外观的 MI 情况下，判定 OK

Shenzhen Hongguang Display Co.,Ltd 9.PACKAGE DRAWING Hongguang Display .