HG101WU008T01
17Pages

Catalog excerpts

Shenzhen Hongguang Display Co.,Ltd CUSTOMER : CUSTOMER MODULE : □Preliminary Specification ■Final Specification Customer Confirmation column： Approved by : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. Hongguang Display

Open the catalog to page 1

Shenzhen Hongguang Display Co.,Ltd Revision History Version NO. Hongguang Display FIRST ISSUE

Open the catalog to page 2

Shenzhen Hongguang Display Co.,Ltd CONTENTS GENERAL INFORMATION I/O CONNECTION & BLOCK DIAGRAM ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS ELECTRO-OPTICAL CHARACTERISTICS RELIABILITY TEST CONDITIONS INSPECTION STANDARDS PACKAGE DRAWING Hongguang Display

Open the catalog to page 3

Shenzhen Hongguang Display Co.,Ltd 1. GENERAL INFORMATION 1.1 1) Structure: TFT PANNEL+IC+FPC+BL 2) IPS Type LCD 1200 dot-segment and 1920 dot-common outputs 3) 16.7M Color can be selected by software 4) White LED back light 5) MIPI-4 interface 6) Operation Temperature : -10~60℃ 7) Storage Temperature : -20~70℃ 8) CTP cover lens ：Dragontrail 9) CTP structure ：G+G 10) LED life time：-/ 1.2 General specification Item of Panel Size Display mode Normally Black Pixel arrangement Active Area Recommended Viewing Direction Hongguang Display

Open the catalog to page 4

Shenzhen Hongguang Display Co.,Ltd 2.DIAGRAM FOR LCM Hongguang Display

Open the catalog to page 5

Shenzhen Hongguang Display Co.,Ltd 3. I/O CONNECTION & BLOCK DIAGRAM 3.1 Power supply for LED anode Power supply for LED cathode A power supply for the logic power and I/O circuit(3.3V) Power Ground DSI-D3+ differential data signals for MIPI interface DSI-D3- differential data signals for MIPI interface Power Ground DSI-D2+ differential data signals for MIPI interface DSI-D2- differential data signals for MIPI interface Power Ground DSI-CLK+ differential clock signals for MIPI interface DSI-CLK- differential clock signals for MIPI interface Power Ground DSI-D1+ differential data signals for...

Open the catalog to page 6

Shenzhen Hongguang Display Co.,Ltd 3.2 block diagram MCU and Display Module Interface Configuration MCU Power Interface Block MIPI Interface Hongguang Display Display Module GND VIO-1.8 VDD-2.8 LEDA LEDK TP-AVDD Interface Block

Open the catalog to page 7

Shenzhen Hongguang Display Co.,Ltd 4. ABSOLUTE MAXIMUM RATINGS (GND=AGND=0V) Backlight Forward Voltage LED Forward Current 5. ELECTRICAL CHARACTERISTICS 5.1 LED backlight specification : 项目 Note:The “LED life time” is defined as the module brightness decrease to 50% of original brightness at IL=20Ma(for each led). The LED life time could be decreased if operating ILis larger than 20mA Note: 28 chips (7 series 4 parallel) connection, LED luminous

Open the catalog to page 8

Shenzhen Hongguang Display Co.,Ltd 5.2 Power ON Hongguang Display

Open the catalog to page 9

Shenzhen Hongguang Display Co.,Ltd 5.3 Power OFF Hongguang Display

Open the catalog to page 10

Shenzhen Hongguang Display Co.,Ltd 6. ELECTRO-OPTICAL CHARACTERISTICS Conditi Item Viewing Angle Contrast Ratio Response Time Normal Viewing angle Hongguang Display

Open the catalog to page 11

Shenzhen Hongguang Display Co.,Ltd Note1 Definition of Contrast Ratio (CR): Note2: Definition of Luminance Uniformity: Active area is divided into 9 measuring areas (Shown in below), every measuring point is placed at the center of each measuring area. FPC The spot locations for luminance measurement V/6 Bmax Bmax: The measured maximum luminance of all measurement position. Bmin: The measured minimum luminance of all measurement position. Note 3:Definition of Response time: Sum of Tr and Tf Display data Optical Response Hongguang Display

Open the catalog to page 12

Shenzhen Hongguang Display Co.,Ltd Note4.Definition of Viewing Angle: The viewing angle range that the CR≥10 Note 5: Definition of Color Chromaticity (CIE 1931) Color coordinate of white & red, green, blue at center point. Hongguang Display

Open the catalog to page 13

Shenzhen Hongguang Display Co.,Ltd 7. RELIABILITY TEST CONDITIONS No Test Item Test Condition STANDARD 1. Functional test is OK. Missing Segment, short, unclear segment, on-display, display abnormally and liquid crystal leak are un-allowed. 2. No low temperature bubbles, end seal loose and fall, frame rainbow. 1. Function test is OK. 2. No glass crack, chipped glass, end seal loose and fall, epoxy frame crack and so on. 3. No structure loose and fall. High Temperature Storage High Temperature Operating Thermal and cold shock Operate at High Temperature and Humidity Vibration Test Dropping...

Open the catalog to page 14

Shenzhen Hongguang Display Co.,Ltd 8. INSPECTION STANDARDS 8.1 AQL Sampling inspection standard 使用 GB/T 2828-2003 一般 II 水平,采用正常检查一次抽样方式；具体抽检方式参照《成品检验管理程序》、《抽样管理规范》缺陷区分 AQL 允收水准严重缺陷 0收1退重缺 0.4 轻缺 1.0

Open the catalog to page 15