SPECIFICATION FOR TFT LCD MODULECUSTOMER:CUSTOMER MODULE :_ HL MODEL : HG097XG008 □Preliminary Specification ■Final Specification Customer Confirmation column: Approved by :Dept. :Data : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document.

1. General Description HG097XG008 is a 1024RGB*768 dots matrix TFT LCD module. It has a TFT panel composed of 1024 sources and 768gates. The LCM can be easily accessed by micro-controller. 2. Features

Backlight current Backlight voltage Chromaticity Coordinatses Without PET GENERAL TOLERANCES CUSTOMER'S CODE: Drawing On/Before 1.Unit:mm 2.Do not scale drawing. 3. n Modification rev.number. 4.Genral Tolerance:±0.2mm 5."*" For important dimension;( ) for reference dimention

(a) Center point on active area. (b)Best Contrast. ★2Uniform measure condition: (1)Measure 9 point. Measure location show below;

8. Module Function Description 8.1Pin Descriptions

深圳市鸿光显示有限公司 8.2 Timing characteristics. Data Input Format Data Input Format for lvds Power On/Off Timing

Dc Electrical Characteristics LVDS mode (Receiver Dil Single-end Signals Differential Signal I Differential Input Voltage

Vertical timing The above “viewing angle” is the measuring position with the largest contrast ratio. Not for good image quality. Viewing direction for good image quality is 12 O’clock. • For panel only •Electro-Optical Characteristics Test Method

深圳市鸿光显示有限公司 .Note2.Definition of Optical Response Time:

10.1MTBF The LCD module shall be designed to meet a minimum MTBF value of 50000 hours with normal 10.2Test condition 1. Judgments should be made after exposure in room temperature for two hours. 2. The distill water is used for the high temperature/humidity test. 3. The sample above is individually for every reliability tests condition. 11. Precautions for using LCD modules. 11.1 Safety (1)Do mot swallow any liquid crystal ,even if there is no proof that liquid crystal is poisonous. (2)If the LCD panel breaks, be careful not to get liquid crystal to touch your skin. (3)If skin is exposed to liquid...

(6) Store in clean environment, free from dust, active gas, and solvent. (7)Do not place the module near organics solvents or corrosive gases. (8)Do not crush, shake, or jolt the module. (9)Avoid static electricity, which can damage the CMOS LSI. (10)The polarizing plate of the display is very fragile, please handle if very carefully. (11)Do not give external shock. (12)DO not apply excessive force on the surface. (13) Do not wipe the polarizing plate with a dry cloth, as it may easily scratch the surface of plate. (14)Do not use ketonics solvent & Aromatic solvent, use with a soft cloth soaked...

13.3. Inspection item and criteria 13.3.1 Visual inspection criterion in immobility 13.3.1.1Glass defectNO Defect item Dimension Unconformity _(Major defect) (Major defect) 1. Linear cracks panel [Reject] 2. Nonlinear crack contrast by limited sample Glass extrude the conductive area (minor defect) a: disregards and no influence assemblage. 1) b ^ 1/3Pin width(non bonding area) [Accept] 2)bonding area^O. 5mm _[Accept] A: Length, b: Width Pin-side ,conductive area damaged (minor defect) (a c: disregards) b^1/3of effective length for bonding electrode [Accept] Pin-side,non-conductive area damaged...

13.3.1.2LCD appearance defect (View area)

13.3.1.4Black tape &Mara tape