Shenzhen Hongguang Display Co.,Ltd CUSTOMER : CUSTOMER MODULE : □Preliminary Specification ■Final Specification Customer Confirmation column： Approved by : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 Revision History Version NO. Hongguang Display FIRST ISSUE

Shenzhen Hongguang Display Co.,Ltd CONTENTS GENERAL INFORMATION I/O CONNECTION & BLOCK DIAGRAM ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS ELECTRO-OPTICAL CHARACTERISTICS RELIABILITY TEST CONDITIONS INSPECTION STANDARDS PACKAGE DRAWING Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 1. GENERAL INFORMATION 1.1 1) Structure: TFT PANNEL+IC+FPC+BL 2) IPS Type LCD 1024 dot-segment and 600 dot-common outputs 3) 16.7M Color can be selected by software 4) White LED back light 5) LVDS-4 interface 6) Operation Temperature : - 20~60℃ 7) Storage Temperature : - 30~70℃ 8) CTP cover lens ：-/ 9) CTP structure ：-/ 10) LED life time：-/ 1.2 General specification Item of Panel Size Display mode Normally White Pixel arrangement Active Area Recommended Viewing Direction Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 2.DIAGRAM FOR LCM Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 3. I/O CONNECTION & BLOCK DIAGRAM 3.1 Common Voltage Power supply for digital circuits and IO pads(3.3V) The signal will reset the LCM, Signal is active low. Standby mode, normally pull high .STBYB= 1 , normal operation STBYB= 0 ,timing control, source driver will turn off, all output are high-Z Power Ground LVDS Negative data signal (-) LVDS Negative data signal (+) Power Ground LVDS Negative data signal (-) LVDS Negative data signal (+) GND RIN2RIN2+ GND LVDS_CLKLVDS_CLK+ GND RIN3RIN3+ GND NC GND NC DIMO SELB AVDD GND LEDL/R U/D VGL NC NC VGH LED+ Power Ground...

Shenzhen Hongguang Display Co.,Ltd 4. ABSOLUTE MAXIMUM RATINGS (GND=AGND=0V) Backlight Forward Voltage LED Forward Current Operating temperature Storage temperature Note: (1) All of the voltages listed above are with respective to GND=0V. (2) Device is subject to be damaged permanently if stresses beyond those absolute maximum ratings listed above. (3) 24 chips (3 series 8 parallel) connection, LED luminous color: WHITE Typical operation conditions : Item Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 5.2 TTL mode DC electrical characteristics 5.3 LVDS mode DC electrical characteristics Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 5.3 TTL mode AC electrical characteristics 5.4 LVDS mode AC electrical characteristics Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 5.5 LVDS mode data input format (8-bit) Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 5.6 Input clock and data timing diagram 5.7 Power on timing sequence Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 5.8 Power off timing sequence Note: Low level=3FH, when NBW=L (Normally white) Low level=00H, when NBW=H (Normally black) Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 6. ELECTRO-OPTICAL CHARACTERISTICS Parameter Contrast Ratio (Center point) Luminance uniformity Response Time WX White WY RX Red Color Chromaticity (CIE 1931) 0.30 θ = 0. Normal viewing angle B/L On Hongguang Display

Shenzhen Hongguang Display Co.,Ltd Note1 Definition of Contrast Ratio (CR): Note2: Definition of Luminance Uniformity: Active area is divided into 9 measuring areas (Shown in below), every measuring point is placed at the center of each measuring area. FPC The spot locations for luminance measurement V/6 Bmax Bmax: The measured maximum luminance of all measurement position. Bmin: The measured minimum luminance of all measurement position. Note 3:Definition of Response time: Sum of Tr and Tf Display data Hongguang Display

Shenzhen Hongguang Display Co.,Ltd Note4.Definition of Viewing Angle: The viewing angle range that the CR≥10 Note 5: Definition of Color Chromaticity (CIE 1931) Color coordinate of white & red, green, blue at center point. Hongguang Displ

Shenzhen Hongguang Display Co.,Ltd 7. RELIABILITY TEST CONDITIONS No Test Item Test Condition STANDARD 1. Functional test is OK. Missing Segment, short, unclear segment, on-display, display abnormally and liquid crystal leak are un-allowed. 2. No low temperature bubbles, end seal loose and fall, frame rainbow. 1. Function test is OK. 2. No glass crack, chipped glass, end seal loose and fall, epoxy frame crack and so on. 3. No structure loose and fall. High Temperature Storage High Temperature Operating Thermal and cold shock Operate at High Temperature and Humidity Vibration Test Dropping test...

Shenzhen Hongguang Display Co.,Ltd 8. INSPECTION STANDARDS 8.1 AQL Sampling inspection standard 使用 GB/T 2828-2003 一般 II 水平,采用正常检查一次抽样方式；具体抽检方式参照《成品检验管 理程序》、《抽样管理规范》 缺陷区分 AQL 允收水准 严重缺陷 0收1退 重缺 0.4 轻缺 1.0

Shenzhen Hongguang Display Co.,Ltd 中尺寸点、线判定标准：（6.2~8 寸以内） 点状缺 陷 （磨伤、 异物、针 1 孔、凹痕、 缺膜、气 泡，白点、 彩点、脏 点） 判定（D 同背面丝印油墨区杂质 区） 判定标准 注：1) D 区的点状缺陷需在不影响 CTP 功能、客户组装及整机的外观的 MI 情况下，判定 OK

Shenzhen Hongguang Display Co.,Ltd 9. PACKAGE Hongguang Display