HG070WS048
25Pages

Catalog excerpts

Shenzhen Hongguang Display Co.,Ltd CUSTOMER : CUSTOMER MODULE : HL MODEL  ■Final Specification Customer Confirmation column： Dept. : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. Hongguang Display

Open the catalog to page 1

Shenzhen Hongguang Display Co.,Ltd Revision History Version NO. FIRST ISSUE Hongguang Display

Open the catalog to page 2

Shenzhen Hongguang Display Co.,Ltd TABLE OF CONTENT   GENERAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS DIMENSIONAL DRAWING TIMING CHARACTERISTICS OF INPUT SIGNAL ELECTRO-OPTICAL CHARACTERISTICS INSPECTION STANDARDS PACKING DRAWING HANDLING PRECAUTION Hongguang Disp

Open the catalog to page 3

Shenzhen Hongguang Display Co.,Ltd  1.0 General Specifications HG070WS048 color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver IC, FPC and a back light unit. The module display area contains 1024x 600pixels. This product accords with RoHS environmental criterion. Viewing direction Full perspective Display Mode Normally White Backlight Type Interface Type Response Time (Tr+Tf) Contrast Ratio Input voltage Hongguang Display

Open the catalog to page 4

Shenzhen Hongguang Display Co.,Ltd 2.0 ABSOLUTE MAXIMUM RATINGS The following are maximum values which, if exceeded may cause fauity operation or damage to the unit Item Digital Supply Voltage Analog Supply Voltage Gate On-Gate Off Voltage Note :If users use the product out off the environment operation range (temperature and humidity ,it will have visual quality concerns. Typical Operation Condition Item Digital Power Supply Voltage For LCD Analog Power Supply Voltage Common Voltage Logic Input Voltage 3.2 BACKLIGHT CHARACTERISTICS Item Forward voltage Connection mode Hongguang Display

Open the catalog to page 5

Shenzhen Hongguang Display Co.,Ltd 4.0 DIMENSIONALDRAWING Hongguang Display

Open the catalog to page 6

Shenzhen Hongguang Display Co.,Ltd 5.0 INTERFACE PIN CONNECTIONS Power for LED backlight (Anode) Power for LED backlight (Cathode) Power ground Common Voltage Digital Power DE/SYNC mode select. Normally pull high H: DE mode. L: HSD/VSD mode Data Enable signal. Vertical sync input. Negative polarity Horizontal sync input. Negative polarity Blue Data Green Data Colock signal Display on/off Left or Right Display Control Up / Down Display Control Analog Power Global reset pin. Active low to enter reset state. Suggest to connecting with an RC reset circuit for stability. Normally pull high....

Open the catalog to page 7

Shenzhen Hongguang Display Co.,Ltd 6.0 Timing characteristics 6.0. Input Timing Table 6.0.2 Clock and Data Timing Diagram Hongguang Display

Open the catalog to page 8

Shenzhen Hongguang Display Co.,Ltd Hongguang Display

Open the catalog to page 9

Shenzhen Hongguang Display Co.,Ltd Hongguang Display

Open the catalog to page 10

Shenzhen Hongguang Display Co.,Ltd Power、Signal sequence Hongguang Display

Open the catalog to page 11

Shenzhen Hongguang Display Co.,Ltd 7.0 ELECTRO-OPTICAL CHARACTERISTICS Panel Transmittance Luminance Uniformity Contrast Ratio Response Time Viewing Angle Color Filter Chromaticity Color gamut （NTSC ratio） Note1: Measurement Setup The LCD module should be stabilized at given temperature for 15 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting backlight for 15 minutes in a windless room.

Open the catalog to page 12

Shenzhen Hongguang Display Co.,Ltd Note2: Definition of Viewing Angle Note3: Definition of Contrast Ratio (CR) The contrast ratio can be calculated by the following expression Contrast Ratio (CR) = L63 / L0 L63: Luminance of gray level 63, L0: Luminance of gray level 0 Note4: Definition of Response Time (TR, TF) Note5: Definition of Luminance Uniformity(Variation) Measure the luminance of gray of gray level 63 at 1-9 points Hongguang Display

Open the catalog to page 13

Shenzhen Hongguang Display Co.,Ltd 8.RELIABILITY 8.1 MTBF The LCD module shall be designed to meet a minimum MTBF value of 50000 hours with normal. (25°C in the room without sunlight) 8.2 TESTS NO. Test Item High Temperature Storage 1 Low Temperature Storage High Temperature Operation Low Temperature Operation High Temperature & Humidity Operation Temperature Cycle Test condition Aftertesting,cosmetic and electrical defects should not happen. Vibration Test Shock Test Drop Test(package state) 800mm, concrete floor,1corner, 3edges, 6 sides each time 10 Electro Static Discharge Test...

Open the catalog to page 14

Shenzhen Hongguang Display Co.,Ltd 9.0 INSPECTION STANDARDS 9.1 Inspection Conditions 9.1.1 Environmental conditions The environmental conditions for inspection shall be as follows Room temperature: 20±3°C ; Humidity: 65±20%RH 9.1.2 The external visual inspection With a single 20-watt fluorescent lamp as the light source, the inspection was in the distance of 30cm or more from the LCD to the inspector's eyes . Major defect A major defect refers to a defect that may substantially degrade usability for product applications. Minor defect A minor defect refers to a defect which is not...

Open the catalog to page 15

Shenzhen Hongguang Display Co.,Ltd 9.5 检验条件

Open the catalog to page 16

9.5.8 检验类型 9.5.8.1 外观检验：产品在非通电状态下观察到的外观、外形、结构等。 9.5.8.2 功能检验：产品电性能、光学特性等。显示区 A 区与 B 区的定义 A区：以屏四边为基准各向屏中心点延伸1/4区域，所剩下的中心区域视为A区（如下图所示）。 B 区：以屏四边为基准各向屏中心点延伸 1/4 的区域，视为 B 区（如下图

Open the catalog to page 17

Shenzhen Hongguang Display Co.,Ltd 9.8 检验标准 9.8.1 功能检查规格判定标准不良项目

Open the catalog to page 18

Shenzhen Hongguang Display Co.,Ltd 画面闪烁 9.8.2 外观检查 9.8.2.1 偏光片外观检查标准判定标准折痕与划伤长≦3mm.0，宽≦0.03mm 接收 1 个，同时必须以正常视角距产品 35 到 40CM,直视 45 度角看不到视 OK 品，反之 NG 偏光片与 LCD 边之间的距离在上、

Open the catalog to page 19

Shenzhen Hongguang Display Co.,Ltd 硅胶未覆盖住 ITO 线硅胶盖住 IC FPC 背面的硅胶未盖主 FPC 金手指 FPC 背面的硅胶总宽度超过 3.0 mm 打胶断续不连贯

Open the catalog to page 20

Shenzhen Hongguang Display Co.,Ltd

Open the catalog to page 21

Shenzhen Hongguang Display Co.,Ltd

Open the catalog to page 22

Shenzhen Hongguang Display Co.,Ltd

Open the catalog to page 23

Shenzhen Hongguang Display Co.,Ltd 将1PCS模组产品装在PE袋包裹。备注：2PCS产品模组的LCD 面对面,第三片模组LCD 第二片模组的背对背使用封口胶封口并贴附唛头 REVSION 版本 DATE 日期 PAGE 页码

Open the catalog to page 24

Shenzhen Hongguang Display Co.,Ltd 11. 0 HANDLING PRECAUTION (1) Don’t disassemble and reassemble the module by self. (禁止自行拆解) (2) Acid, alkali, alcohol or touched directly by hand will damage the display. (酸性、碱性、酒精或手的直接接触将会损伤显示面) (3) Static electricity will damage the module. Please configure grounding device. (静电会损伤模组，请装配接地设备) (4)The strong vibration, shock, twist or bend will cause material damage, even module broken. (强烈的撞击、震动、扭转或弯曲将会造成原材损伤，甚至面板破裂) (5) It is easy to cause image sticking while displaying the same pattern for very long time. (长期显示同一画

Open the catalog to page 25