HG070WS013
24Pages

Catalog excerpts

Shenzhen Hongguang Display Co.,Ltd CUSTOMER : CUSTOMER MODULE : HL MODEL  Preliminary Specification ■Final Specification Customer Confirmation column： Approved by : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. Hongguang Display

Open the catalog to page 1

Shenzhen Hongguang Display Co.,Ltd Record of Revision Version Revise Date Page Initial Release. Update Backlight power consumption& Panel power consumption& Weight Update Operation Specifications Update Input signal voltage Update Current Consumption& Conditions Update Optical Specifications Update Packaging Material Table Update Current Consumption Update Safety Modify Mechanical Drawing Modify Package Drawing First Final Release for P070BAG-CM1 19 Modify Mechanical Drawing Modify Mechanical Pixel size. Hongguang Display Model name change from P070BAG-CM1 to NJ070NA-23A Modify Reliability...

Open the catalog to page 2

Hongguang Display

Open the catalog to page 3

Shenzhen Hongguang Display Co.,Ltd 1. General Specifications The specification HG070WS013 is a 7 ”(1024x600) TFT Liquid Crystal Display module with LED Backlight unit , 40 pin LVDS interface, normally Black transmissive display mode. This module will be applied to Consumer Electronics(CE Application) Driver element Display mode Normally Black Pixel size Active area Module size Surface treatment Hard Coating Color arrangement View direction(Gray Inversion) ALL Backlight power consumption Panel power consumption Hongguang Display

Open the catalog to page 4

Shenzhen Hongguang Display Co.,Ltd 2. Pin Assignment FPC Connector is used for the module electronics interface. The recommended model is FH12A-40S-0.5SH manufactured by Hirose. Function Common Voltage Power Voltage for digital circuit Power Voltage for digital circuit Standby mode, Normally pulled high STBYB = “1”, normal operation STBYB = “0”, timing controller, source driver will turn off, all output are High-Z - LVDS differential data input + LVDS differential data input - LVDS differential data input + LVDS differential data input - LVDS differential data input + LVDS differential data...

Open the catalog to page 5

Shenzhen Hongguang Display Co.,Ltd 22 Backlight CABC controller signal output Power for Analog Circuit Horizontal inversion Vertical inversion I: input, O: output, P: Power Note1: If LVDS input data is 6 bits ,SELB must be set to High; If LVDS input data is 8 bits ,SELB must be set to Low. Note2: When CABC_EN=”00”, CABC OFF. When CABC_EN=”01”, user interface image. When CABC_EN=”10”, still picture. When CABC_EN=”11”, moving image. When CABC off, don’t connect DIMO, else connect it to backlight. Note3: When L/R=”0”, set right to left scan direction. When L/R=”1”, set left to right scan...

Open the catalog to page 6

Shenzhen Hongguang Display Co.,Ltd Note: Definition of scanning direction. Refer to the figure as below: Hongguang Display

Open the catalog to page 7

Shenzhen Hongguang Display Co.,Ltd 3. Operation Specifications 3.1. Absolute Maximum Ratings (Note 1) Values Item Operation Temperature Storage Temperature Power voltage Note 1: The absolute maximum rating values of this product are not allowed to be exceeded at any times. Should a module be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be recovered, or in an extreme case, the module may be permanently destroyed. Hongguang Display

Open the catalog to page 8

Shenzhen Hongguang Display Co.,Ltd 3.1.1. Typical Operation Conditions ( Note 1) Values Item Input logic high voltage Input logic low voltage Power voltage Input signal voltage Note 1: Be sure to apply DVDD and VGL to the LCD first, and then apply VGH Note 2: DVDD setting should match the signals output voltage (refer to Note 3) of customer’s system board. Note 3: LVDS, Reset. Note 4: Typ. VCOM is only a reference value, it must be optimized according to each LCM. Be sure to use VR; Hongguang Display

Open the catalog to page 9

Shenzhen Hongguang Display Co.,Ltd 3.1.2. Current Consumption Values Item IDVDD IAVDD 3.1.3. Backlight Driving Conditions Values Item Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and IL =265mA. Note 2: The “LED life time” is defined as the module brightness decrease to 50% original brightness at Ta=25℃ and IL =200mA. The LED lifetime could be decreased if operating IL is lager than 265mA. Hongguang Display

Open the catalog to page 10

Shenzhen Hongguang Display Co.,Ltd 3.2. Power Sequence a. Power on: <20ms VDD STBYB LVDS Signal AVDD VCOM RESET LVDS Signal Normal signal Hongguang Display

Open the catalog to page 11

Shenzhen Hongguang Display Co.,Ltd 3.3. Timing Characteristics 3.3.1. AC Electrical Characteristics Clock frequency Input data skew margin Clock high time 3.3.2. Input Clock and Data Timing Diagram Hongguang Display

Open the catalog to page 12

Shenzhen Hongguang Display Co.,Ltd 3.3.3. DC Electrical Characteristics Parameter Differential input high Threshold voltage Differential input low Threshold voltage Input voltage range (singled-end) Differential input common mode voltage Differential voltage Differential input leakage current Hongguang Display

Open the catalog to page 13

Shenzhen Hongguang Display Co.,Ltd 3.3.4. Timing Values Item Clock Frequency Horizontal display area Vertical display area Hongguang Display

Open the catalog to page 14

Shenzhen Hongguang Display Co.,Ltd 3.3.5. Data Input Format 6bit LVDS input Note: Support DE timing mode only, SYNC mode not supported. Hongguang Display

Open the catalog to page 15

Shenzhen Hongguang Display Co.,Ltd 4. Optical Specifications Item Unit Remark Min. Typ. Max. T% (w/o APCF, w/o haze) @ C-light Center All left side data are based Note (1) on INX’s following condition (at 25 ℃) Center ms 1. LC : AAS Note (2) 2.BLU : under C_light 3.Machine : DMS-900 V LC : Vbright ≧ 5.3V deg Note (3) Vdark ≦ 0.3V -- Green Gy CF only Chromaticity (CIE1931) Viewing normal angle θx=θy=0° CF Glass with C-light White NTSC *Note (1) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L255 / L0 L 255 :...

Open the catalog to page 16