Shenzhen Hongguang Display Co.,Ltd CUSTOMER : CUSTOMER MODULE : HL MODEL  Preliminary Specification ■Final Specification Customer Confirmation column： Approved by : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. Hongguang Display

Shenzhen Hongguang Display Co.,Ltd REVISION STATUS Version Revise Date Hongguang Display First Issued.

Shenzhen Hongguang Display Co.,Ltd TABLE OF CONTENTS NO. Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 1. GENERAL DESCRIPTION 1.1 DESCRIPTION This LCM is a color active matrix thin film transistor (TFT) IPS liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. It is composed of a TFT LCD panel, Driver IC, FPC and Backlight.This TFT LCD has a 6.86-inch diagonally measured active display area with (480 horizontal by 1280 vertical pixel) resolution. Panel Size Active Area Pixel Pitch Outline Dimension Display Mode Transmission mode, normally black Viewing Direction Full viewing Display Format Surface Treatment Operation Temperature...

Hongguang Display 4. DRIVER IC:(来料FOG) 5. LCM(White): Brightness(centre point): Chromaticity(centre point) : X:0.260MIN) 0.360(MAX); Y:0.280(MIN) 0.380(MAX). Uniformity( 9 AVG 1/6):70%(MIN),75%(TYP) 6. BACK LIGHT: 12 chip white LEDs If=30mA/LED,Vf=9.0-10.8V 7. OPERATING TEMP: -10°C TO 50°C,STORAGE TEMP: -20°C TO 60°C 8. * Critical Parameter,( ) ref Parameter, cpk Parameter Unspecified Tolerances:±0.50mm Modification mark: n 9. SUGGESTION:TP window size unilateral increase 0.3~0.5mm than LCM A.A 10.REQUIREMENTS ENVIRONMENTAL PROTECTION: RoHS NOTES: 1. DISPLAY TYPE: 6.86", TFT LCD 2. DISPLAY MODE:...

Shenzhen Hongguang Display Co.,Ltd 3. PIN DESCRIPTION FPC Connector is used for the module electronics interface. No. Symbol Function 1 GND Ground 2 MIPI-D0P Positive MIPI differential data input 3 MIPI-D0N Negative MIPI differential data input 4 GND Ground 5 MIPI-D1P Positive MIPI differential data input 6 MIPI-D1N Negative MIPI differential data input 7 GND Ground 8 MIPI-CLKP Positive MIPI differential clock input 9 MIPI-CLKN Negative MIPI differential clock input 10 GND Ground 11 MIPI-D2P Positive MIPI differential data input 12 MIPI-D2N Negative MIPI differential data input 13 GND Ground...

Shenzhen Hongguang Display Co.,Ltd 4. ELECTRICAL CHARACTERISTICS 4.1 ABSOLUTE MAXIMUM RATINGS Item Digital Supply Voltage Digital Supply Voltage Supply Voltage Supply Voltage Values Unit Remark Typ. Min. Max. Digital Supply Voltage VDD 3.0 3.3 3.6 V Digital Supply Voltage IOVCC 1.6 1.8 2.0 V VIH 0.7VDD VDD V Logic Input Voltage VIL GND 0.3VDD V Note1: Please adjust VCOM to make the flicker level be minimum Note2:TYP VCOM is only reference value. It must be optimized according to each LCM. Be sure to use VR and OP buffer on VCOM output. Please adjust VCOM to make the flicker level be minimum for...

Shenzhen Hongguang Display Co.,Ltd 4.3 BACKLIGHT UNIT Item LED Current Forward voltage Reverse current Power dissipation Peak forward current Reverse Voltage Internal Circuit Diagram K A Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 4.4 POWER ON/OFF SEQUENCE Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 5.INPUT SIGNAL TIMING 5.1 MODE DC ELECTRICAL CHARACTERISTICS Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 5.2 AC CHARACTERISTICS Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 5.3 PARALLEL RGB INPUT Hongguang Display TIMING TABLE

Shenzhen Hongguang Display Co.,Ltd 6.OPTICAL CHARACTERISTICS Item Contrast Ratio Luminous tolerance Response Time Viewing Angle K=Contrast Ratio>10 Green Blue White Color gamut 55 (NTSC ratio) Note1: Definition of optical measurement system (BM-7) Note2: Definition of viewing angle range and measurement system Viewing angle is measured at the center point of the LCD by CONOSCOPE (ergo-80). Normal line θ= =0° Active Area Note3: Definition of Response time Hongguang Display

Shenzhen Hongguang Display Co.,Ltd The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from 10% to 90%. Photo detector output (Relative value) Fig. 6-3 Definition of response time Note4: Definition of contrast ratio Luminance measured when LCD on the Whitestate Contrast ratio(CR)= Luminance measured when LCD on the Blackstate “White state “: The state is that the...

Shenzhen Hongguang Display Co.,Ltd 7.RELIABILITY TEST ITEMS 7.1 TEMPERATURE Test Item Test Condition High Temperature Storage Low Temperature Storage High Temperature Operation Low Temperature Operation High Temperature High Humidity Operation Thermal Shock Image Sticking 25℃ ; 1hrs Note1 Note1:Condition of image sticking test :25℃±2℃ Operation with test pattern sustained for 1 hrs,then change to gray pattern immediately.after 5 mins,the mura must be disappeared completely 7.2 VIBRATION&SHOCK Test item Packing Shock (non-operation) Packing Vibration (non-operation) Conditions 980m/s2,6ms, ±x,y,z...

Shenzhen Hongguang Display Co.,Ltd 8. GENERAL PRECAUTION 8.1 SAFETY 1. Do not swallow any liquid crystal, even if there is no proof that liquid crystal is poisonous. 2. If the LCD panel breaks, be careful not to get liquid crystal to touch your skin. 3. If skin is exposed to liquid crystal, wash the area thoroughly with alcohol or soap. 1. Store the panel or module in a dark place where the temperature is 23±5°C and The humidity is below 50±20%RH. 2. Store in anti-static electricity container. 3. Store in clean environment, free from dust, active gas, and solvent. 4. Do not place the module near...

Shenzhen Hongguang Display Co.,Ltd 9. INSPECTION STANDARDS 9.1 I ncoming inspection right (1) The Incoming Inspection Standard will be agreed and signed by both sides(Customer an starry) Viewing distance is approximately 35~40 cm Viewing angle is normal to the LCD panel as Fig-1(30°) Ambient temperature is approximately 25±5℃ Ambient humidity is 60±5%RH Ambient illuminance is from 300~500 Lux Input signal timing should be typical value Mura & Light leakage inspection an ND-Filter 5% Special condtion (1) Viewing distance is close for inspection of adjacent dots and distance between defect Dots...