Shenzhen Hongguang Display Co.,Ltd CUSTOMER : CUSTOMER MODULE : HL MODEL  Preliminary Specification ■Final Specification Customer Confirmation column： Approved by : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. Hongguang Display

Shenzhen Hongguang Display Co.,Ltd CONTENT LIST Hongguang Display

Shenzhen Hongguang Display Co.,Ltd Record of Revisions Revision Hongguang Display Initial Released

Shenzhen Hongguang Display Co.,Ltd 1.0 GENERAL DESCRIPTION 1.1 Introduction HG050QZ002 is a color active matrix TFT-LCD Panel using LTPS TFT's (Thin Film Transistors) as an active switching devices. This model is composed of a TFT-LCD Panel, a driving circuit and a back light system. It is a transmissive type display operating in the normal black. This TFT-LCD has a 5.0 inch diagonally measured active area with FHD resolutions (1080 horizontal by 1080 vertical pixel array). Each pixel is divided into Red, Green, Blue dots which are arranged in 1pixel 2 domain and this panel can display 16.7M...

Shenzhen Hongguang Display Co.,Ltd 1.3 General Specifications (H: horizontal length, V: vertical length) Parameter Pixel Pitch Active Area Pixel Arrangement Display Colors Color Gamut Display Mode Normally Black, Transmissive mode Dimensional Outline Viewing Direction (Human Eye) Note: 136.531x132.208x1.98 U/D/L/R free viewing direction 1. At the U/D/L/R direction, the viewing angle is same; 2. The TFT and CF LC Algin Direction; Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 2.0 ABSOLUTE MAXIMUM RATINGS The absolute maximum ratings are list on table as follows. When used out of the absolute maximum ratings, the LSI may be permanently damaged. Using the LSI within the following electrical characteristics limit is strongly recommended for normal operation. If these electrical characteristic conditions are exceeded during normal operation, the LSI will malfunction and cause poor reliability. Spec Parameter Symbol Unit Min. Max. Typ. Logic Power Supply Voltage Analog Positive Power Supply Analog Negative Power Supply Back-light Power...

Shenzhen Hongguang Display Co.,Ltd 3.0 ELECTRICAL SPECIFICATIONS 3.1 TFT LCD Module DC Characteristics Parameter Power Supply Input Voltage Analog Positive Power Supply Analog Negative Power Supply Low Level Input Voltage High Level Input Voltage Power Consumption Unit Remark - Note: Frame rate=60HZ, Typ. Pattern White pattern, worst case pattern 1×1 checker 25℃. 3.2 Backlight Driving Conditions Parameter Notes: 1. Calculator Value for reference ILED×VLED×LED Quantity = PLED 2. The LED Life-time define as the estimated time to 50%30000hrs degradation of initial luminous. Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 3.3 Block Diagram Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 4.0 INTERFACE CONNECTION 4.1 Connector Part Number Connector Name / Designation Manufacturer Connector Model Number Signal Connector Hirose DF40C-50DP-0.4V 4.2 Electrical Interface Connection Pin NO. Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 5.0 SIGNAL TIMING SPECIFICATION Vertical Timing Hongguang Display

Shenzhen Hongguang Display Co.,Ltd Horizontal Timing Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 6.0 POWER ON/OFF SEQUENCE Power on/off Sequence Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 7.0 OPTICAL SPECIFICATIONS 7.1 Overview The test of Optical specifications shall be measured in a dark room(ambient luminance≤ 1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Topcon SR-UL1R and Westar TRD-100A) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°.The center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement. 7.2 Optical Specifications Parameter Symbol Condition...

Shenzhen Hongguang Display Co.,Ltd 3. Surface luminance is the center point across the LCD surface 50cm from the surface with all pixels displaying white. This measurement shall be taken at the locations shown in FIG. 1. 4. Uniformity measurement shall be taken at the locations shown in FIG. 2, for a total of the measurements per display, measure surface luminance of these nine points across the LCD surface 50cm from the surface with all pixels displaying white. Uniformity Min Luminance of 9 points Max Luminance of 9 points 5. The color chromaticity coordinates specified in Table1 shall be calculated...

Shenzhen Hongguang Display Co.,Ltd Figure 3. Response Time Testing Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 8.0 MECHANICAL CHARACTERISTICS 8.1 Dimension Requirements for LCD Part Mechanical outlines for the panel (H: horizontal length, V: Vertical length) Parameter Panel size Active area Number of pixels Pixel pitch Pixel arrangement Dimensional outline Normally Black Display mode Figure 5. LCM Outline Dimension (unit: mm) Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 9.0 RELIABILITY TEST NO. Test Item Test Condition High Temp Operation High Temp/ High humidity Operation High Temp Storage High Temp/ High Humidity Storage Thermal Shock Hongguang Display 60 ℃/ 90% RH for 100 hours 75 ℃ for 240 hours 65 ℃/ 90% RH for 100 hours -30 ℃ for 240 hours -30 ℃ for 45min and then 75 ℃ for 45 min, 5 cycles Contact=4KV,Air=8KV

Shenzhen Hongguang Display Co.,Ltd 10.0 PACKING METHOD Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 12.0 HANDDLING & CAUTIONS 12.1 Mounting Method  The panel of the LCM consists of two thin glasses with polarizer which easily get damaged. So extreme care should be taken when handling the LCM.  Excessive stress or pressure on the glass of the LCM should be avoided. Care must be taken to insure that no torsional or compressive forces are applied to the LCM unit when it is mounted.  If the customer's set presses the main parts of the LCM, the LCM may show the abnormal display. But this phenomenon does not mean the malfunction of the LCM and should be pressed...