customer module :_ Customer Confirmation column: Approved by : Dept. :Data : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 Revision History Version NO. HongGuang Display Co.,Ltd FIRST ISSUE 盖板增加感

深圳市鸿光显示有限公司 CONTENTS GENERAL INFORMATION I/O CONNECTION & BLOCK DIAGRAM ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS ELECTRO OPTICAL CHARACTERISTICS RELIABILITY TEST CONDITIONS INSPECTION STANDARDS PACKAGE DRAWING HongGuang Display Co.,Ltd

1) Structure: AMOLED oncell+IC+FPC+LENS 2) IPS Type LCD 720 dot-segment and 1280 dot-common outputs 3) 16.7M Color can be selected by software 4) White LED back light 8) CTP cover lens :Corning HongGuang Display Co.,Ltd

HongGuang Display Co.,Ltd

I: Input; O: Output; P: Power HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 3.2 block diagram MCU and Display Module Interface Configuration MCU Power Interface Block MIPI Interface HongGuang Display Co.,Ltd Display Module GND VIO-1.8 VDD-2.8 TP-IOVCC TP-VCC Interface Block

1. VDDI=1.65 to 3.3V, VDD=2.5 to 4.8V, VSSI=VSS=DVSS=0V, VDD means VDDA, VDDR, VDDB. And VSS means VSSA, VSSR, VSSB, AVSS, and VSSAM. VDDB, VDDA and VDDR should be the same input voltage level and larger than VDDI voltage.

Note LwltHigh i*r*rl low lo^els. $petifi*d 3 a 2Q% and 30% ui IQVOG fcn Input signals Note: S -30 Lo 7D ’C, IOVCC=1 65V to 3.3V. VDD=2.5V 10 3.0V. GND=-3V HongGuang Display Co.,Ltd

Rcsel input liming I ovcc« 1 ■ ffi (0 3 ffV. VD1>2 5 JO 3 fiV. AGND-OGM[>0 V, fa-JO to 6E t HongGuang Display Co.,Ltd HG050HD030T01 10/18

5.5 Power Off Sequence VDQ RSTE OISPOF# Mode MIP1

6. ELECTRO-OPTICAL CHARACTERISTICS Item HongGuang Display Co.,Ltd

Definition of Contrast Ratio (CR): Note2: Definition of Luminance Uniformity: Active area is divided into 9 measuring areas (Shown in below), every measuring point is placed at the center of each measuring area. FPC The spot locations for luminance measurement V/6 Bmax Bmax: The measured maximum luminance of all measurement position. Bmin: The measured minimum luminance of all measurement position. Note 3:Definition of Response time: Sum of Tr and Tf Display data Optical Response HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 Note4.Definition of Viewing Angle: The viewing angle range that the CR≥10 Note 5: Definition of Color Chromaticity (CIE 1931) Color coordinate of white & red, green, blue at center point.

NOTE: 1. The reliability items will be fully performed in new sample qualification, 2 .The reliability status will be tested as monitor during mass production. Individual reliability test shall be performed by lot , Moreover, the individual reliability item shall be decided according to reliability plan. 3. All samples are inspected after keeping in the room with normal temperature and humidity for 2 hours or above. 4. Vibration test: It is not necessary to test for those products without assembly frame , backlight , PCB and so on. 5. Dropping test : It is necessary for affirming new package....

HongGuang Display Co.,Ltd ）等 维纤、屑 毛 、伤 划 感无 、 伤 磨（ 陷 缺 状线 ）内以寸 2.6（：准标定判线、点寸尺小 。等等)时要 必(镜微显体实,镜大放,尺卡标游,卡比对林菲,机片单及线源电,板主,架测测电:具工验检 9.2.8 。秒 3-秒 1：间时验检，XUL0001-XUL006 为度照 :境环验检观外,下以 XUL002 为度照:境环验检测

HongGuang Display Co.,Ltd

深圳市鸿光显示有限公司 DRAWING