SPECIFICATION FOR AMOLED MODULE CUSTOMER : CUSTOMER MODULE : HG MODEL □Preliminary Specification ■Final Specification Customer Confirmation column： Approved by : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document.

深圳市鸿光显示有限公司 Revision History Version NO. FIRST ISSU

深圳市鸿光显示有限公司 CONTENTS GENERAL INFORMATION I/O CONNECTION & BLOCK DIAGRAM ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS ELECTRO OPTICAL CHARACTERISTICS RELIABILITY TEST CONDITIONS INSPECTION STANDARDS PACKAGE DRAWING

深圳市鸿光显示有限公司 1. GENERAL INFORMATION 1.1 1) Structure: AMOLED+IC+FPC 2) IPS Type LCD 720 dot-segment and 1280 dot-common outputs 3) 16.7M Color can be selected by software 4) MIPI-4interface 5) OperationTemperature:-40~70℃ 1.2 General specification Item of Panel Size Display mode Normally Black Pixel arrangement Active Area Recommended Viewing Direction HongGuang Displa

深圳市鸿光显示有限公司 3. I/O CONNECTION & BLOCK DIAGRAM Power IC Input Voltage Power Ground The signal will reset the LCM, Signal is active low. The signal will reset the LCM, Signal is active low. A power supply for the logic power and I/O circuit(1.8V) Power Ground DSI-D2+ differential data signals for MIPI interface DSI-D2- differential data signals for MIPI interface Power Ground DSI-D1+ differential data signals for MIPI interface DSI-D1- differential data signals for MIPI interface Power Ground DSI-CLK+ differential clock signals for MIPI interface DSI-CLK- differential clock signals for MIPI interface...

深圳市鸿光显示有限公司 3.2 block diagram MCU and Display Module Interface Configuration MCU Power Interface Block MIPI Interface

深圳市鸿光显示有限公司 4. ABSOLUTE MAXIMUM RATINGS 5. ELECTRICAL CHARACTERISTICS 5.1 DC characteristics Notes: 1. VDDI=1.65 to 3.3V, VDD=2.5 to 4.8V, VSSI=VSS=DVSS=0V, VDD means VDDA, VDDR, VDDB. And VSS means VSSA, VSSR, VSSB, AVSS, and VSSAM. VDDB, VDDA and VDDR should be the same input voltage level and larger than VDDI voltage. 2. TA = -30 to 85

深圳市鸿光显示有限公司 5.2 AC Characteristics 5.31 Serial Interface Characteristics Symbol Parameter MIN MAX Unit Description TSCYC Clock cycle (Write) 100 ns TSCYC Clock cycle (Read) 300 ns TSCH Clock “H” pulse width (Write) 40 ns TSCH Clock “H” pulse width (Read) 140 ns SCL TSCL Clock “L” pulse width (Write) 40 ns TSCL Clock “L” pulse width (Read) 140 ns TSCr Clock rise time 5 ns TSCf Clock fall time 5 ns TCSU Chip select setup time 20 ns nCS TCH Chip select hold time 50 ns TSISU Data input setup time 20 ns SDI TSIH Data input hold time 20 ns TSOD Data output setup time 120 ns SDO TSOH Data output hold...

深圳市鸿光显示有限公司 5.32 DSI Timing Characteristics HS Data Transmission Burst CLK THS-ZERO Disconnect Terminator VIH(min) VIL(max) HS clock transmission Disconnect Terminator Clock Lane CLKp/CLKn VIH(min) VIL(max) Data Lane Dp/Dn Disconnect Terminator VIH(min) VIL(max) 5.33 Reset Timing Shorter than tRESW Normal Operation Resetting Internal Status Reset input timing: IOVCC=1.65 to 3.6V, VDD=2.5 to 3.6V, AGND=DGND=0V, Ta=-40 to 85℃ Initial Condition ( Default for H /W reset) Related Pins *1) Reset low pulse width *2) Reset complete time - When reset applied during Sleep in mode When reset applied during...

深圳市鸿光显示有限公司 5.4 Power On Sequence

深圳市鸿光显示有限公司 6. ELECTRO-OPTICAL CHARACTERISTICS Mode Full White @500 Nits IVCI IVDDIO Conditi Item Viewing Angle Contrast Ratio Normal Viewing angle

Definition of Contrast Ratio (CR): Note2: Definition of Luminance Uniformity: Active area is divided into 9 measuring areas (Shown in below), every measuring point is placed at the center of each measuring area. FPC The spot locations for luminance measurement Luminance Uniformity = Bmax: The measured maximum luminance of all measurement position. Bmin: The measured minimum luminance of all measurement position. Note 3:Definition of Response time: Sum of Tr and Tf Display data

深圳市鸿光显示有限公司 Note4.Definition of Viewing Angle: The viewing angle range that the CR≥10 Note 5: Definition of Color Chromaticity (CIE 1931) Color coordinate of white & red, green, blue at center point

深圳市鸿光显示有限公司 7. RELIABILITY TEST CONDITIONS No Test Item High Temperature Storage High Temperature Operating Thermal and cold shock Operate at High Temperature and Humidity Vibration Test Dropping test Test Condition 1. Functional test is OK. Missing Segment, short, -50°C / 96Hours unclear segment, on-display, display +70°C / 96Hours abnormally and liquid -40°C / 96Hours crystal leak are -40°C +70°C x 10cycles un-allowed. (30min) (5min) (30min) 2. No low temperature bubbles, end seal loose 60°C x 90%RH / 24H and fall, frame rainbow. Frequency: 1. Function test is OK. 10Hz~55Hz~10Hz 2. No glass...

深圳市鸿光显示有限公司 8. INSPECTION STANDARDS 8.1 AQL Sampling inspection standard 使用 GB/T 2828-2003 一般 II 水平,采用正常检查一次抽样方式；具体抽检方式参照《成品检验管 理程序》、《抽样管理规范》 缺陷区分 AQL 允收水准 严重缺陷 0收1退 重缺 0.4 轻缺 1.0

同背面丝印油墨区杂质 判定标准