Shenzhen Hongguang Display Co.,Ltd CUSTOMER : CUSTOMER MODULE : HL MODEL  ■Final Specification Customer Confirmation column： Dept. : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document. Hongguang Display

Shenzhen Hongguang Display Co.,Ltd Revision History Version NO. FIRST ISSUE Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 1.General Description HG040HH005 is a color active matrix TFT LCD module using amorphous MIPI Signal silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 4 . 0 inch diagonally measured active area with HD resolutions (720 horizontal by 720 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type. MIPI RX RESET Driver IC 3.3V Pixel pitch Active...

Shenzhen Hongguang Display Co.,Ltd 3.Outline Dimension Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 4.Interface Definition Pin No. LEDA LEDA LEDA NC LEDK LEDK LEDK LEDK GND GND D2+ D2GND D1+ D1GND CLK+ CLKGND D0+ D0GND D3+ D3GND IOVCC RST(GRB) GND IOVCC_1.8V VCC_3.3V Hongguang Display Backlight Anode Backlight Anode Backlight Anode No Connection Backlight Cathode Backlight Cathode Backlight Cathode Backlight Cathode Ground Ground MIPI differential data input (Positive) MIPI differential data input (Negative) Ground MIPI differential data input (Positive) MIPI differential data input (Negative) Ground MIPI differential clock input (Positive) MIPI differential...

Shenzhen Hongguang Display Co.,Ltd 5. Operation Specifications 5.1 Absolute Max. Rating The following are maximum values which，if exceeded，may cause faulty operation or damage to the unit. Values Item Symbol Unit Remark Min. Max. IOVCC V Power Voltage VCC -0.3 3.6 V AVEE V IOVCC Input Signal Voltage VI -0.3 V Operation Temperature TOP -20 70 ℃ Storage Temperature TST -30 80 ℃ Note: The absolute maximum rating values of this product are not allowed to be exceeded at any times. Should a module be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be...

Shenzhen Hongguang Display Co.,Ltd 5.3 Back-Light Unit Characeristics The back-light system is an edge-lighting type with back-light are shown in the following tables. white LEDs. The characteristics of the Forward Voltage Forward current Note: 1. The figure below shows the connection of backlight LED. 2. One LED: IF=90mA, VF=2.9V Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 6.Signal Timing Characteristics 6.1 Power on/off Sequence BOOSTM[1:0]=10 (Internal DC/DC power mode : Charge Pump, FP7721) VCCD=IOVCC=VCCH=1.65V ~ 3.6V, VCI=VCIP=2.5V ~ 4.8V. Video data Power Status SLPOUT Mode SLPIN Mode DISOFF 0x28h 6.2 Timing Parameters Parameter MIPI digital operation current. MIPI digital stand-by current. Hongguang Display

Shenzhen Hongguang Display Co.,Ltd MIPI Characteristics for High Speed Receiver Single-ended input low voltage Single-ended input high voltage Common-mode voltage Differential input impedance HS transmit differential voltage(VOD=VDP-VDN). MIPI Characteristics for Low PowerReceiver VI Output high level Pad signal voltage range. Ground shift. Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 7.Optical specifications Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 5 minutes in a dark environment at 25℃. Parameter Symbol Condition Horizontal Viewing Angle range Vertical Luminance Contrast ratio White luminance uniformity White Chromaticity Blue Response Time (Rising + Falling) Θ = 0 (Center) Normal Viewing Angle Note 2 @Silicate BLU POL:HC+ Clear Note 3 Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction...

Shenzhen Hongguang Display Co.,Ltd 5. The electro-optical response time measurements shall be made as FIGURE 1 shown in Appendix. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Tf. 8. Reliability Test Items No Test Items High temperature storage test Low temperature storage test High temperature operation test Low temperature operation test High temperature & high humidity operation test Thermal shock Note： 1. After the reliability test, the product only guarantee function normally without any fatal defect (non-display, line defect, abormal display etc )....

Shenzhen Hongguang Display Co.,Ltd 9. Packing and Label Format Hongguang Display

Shenzhen Hongguang Display Co.,Ltd 10.0 PRECAUTIONS (1) Use fingerstalls with soft gloves in order to keep display clean during the incoming inspection and assembly process. (2) You must mount a module using specified mounting holes (Details refer to the drawings). (3) Please make sure to avoid external forces applied to the Source PCB or FPC and D-IC during the process of handling or assembling. If not, It causes panel damage or malfunction. (4) Note that LCD surface are very fragile and could be easily damaged. Do not touch, push or rub the exposed LCD surface with glass, tweezers or anything...

Shenzhen Hongguang Display Co.,Ltd 10.2 Operating Precautions (1) Be careful for condensation at sudden temperature change. Condensation makes damage to LCD surface or electrical contacted parts. And after fading condensation, smear or spot will occur. (2) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimized the interference. (3) The electrochemical reaction caused by DC voltage will lead to LCD degradation, so DC drive should be avoided. (4) The LCD modules...

Shenzhen Hongguang Display Co.,Ltd 10.3 Electrostatic Discharge Control (1) Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly. Keep products as far away from static electricity as possible. (2) Avoid the use work clothing made of synthetic fibers. We recommend cotton clothing or other conductivity-treated fibers. 10.5 Precautions for Strong Light Exposure Strong light exposure causes degradation of polarizer and color filter....