SPECIFICATION FOR TFT LCD MODULE CUSTOMER: CUSTOMER MODULE :_ Customer Confirmation column: Approved by :Dept. :Data : Please return one of the copies of the specification with your signature to us within two weeks after you receive this document.If it is not returned,we will assume that you agree to the entire contents of this specification document.

深圳市鸿光显示有限公司 CONTENTS PAGE 5.1 D.C ELECTRICAL CHARACTERISTICS 5.2 ELECTRO-OPTICAL CHARACTERISTICS 7.1 FUNCTION BLOCK DIAGRAM 7.2 PANEL LAYOUT DIAGRAM 7.3 PIN ASSIGNMENTS 7.4 GRAPHIC DISPLAY DATA RAM ADDRESS MAP 7.5 INTERFACE TIMING CHART 8. POWER ON / OFF SEQUENCE & APPLICATION CIRCUIT 8.1 POWER ON / OFF SEQUENCE 8.2 APPLICATION CIRCUIT 8.3 INITIAL CODE 8.4 COMMAND TABLE 9. RELIABILITY TEST CONDITIONS 12. OUTGOING INSPECTION PROVISION

深圳市鸿光显示有限公司 1. WARRANTY Supplier warrants that the products delivered pursuant to this specification (or order) will conform to the agreed specifications for twelve (12) months from the shipping date ("Warranty Period"). Supplier is obligated to repair or replace the products which are found to be defective or inconsistent with the specifications during the Warranty Period without charge, on condition that the products are stored in the original packages at 25°C±5°C, 55% ±10%RH or used as the conditions specified in the specifications. Nevertheless, Supplier is not obligated to repair or replace...

深圳市鸿光显示有限公司 3. MECHANICAL DATA NO Aperture Rate Active Area Panel Size Module Size * Panel thickness includes substrate glass, cover glass and UV glue thickness.

5.2 ELECTRO-OPTICAL CHARACTERISTICS PANEL ELECTRICAL SPECIFICATIONS (1) Normal mode condition : - Vcc = 12.5V - Contrast setting : 0X80 - Frame rate : 105Hz - Duty setting : 1/64 (2) Sleep mode condition : When send 0xae command OLED display off and memory data will be maintained.

Note: (A) Under Vcc= 12.5V, Ta = 25°C, 50% RH. (B) Life time is defined the amount of time when the luminance has decayed to less than 50% of the initial measured luminance. (1) Setting of 120 cd/m2 : - Contrast setting : 0x80 - Frame rate : 105Hz - Duty setting : 1/64

深圳市鸿光显示有限公司 7. INTERFACE 7.1 FUNCTION BLOCK DIAGRAM IREF VCOMH VLSS 7.2 PANEL LAYOUT DIA DIAGRAM

深圳市鸿光显示有限公司 7.4 GRAPHIC DISPLAY DATA RAM ADDRESS MAP The GDDRAM is a bit mapped static RAM holding the bit pattern to be displayed. The size of the RAM is 128 x 64 bits and the RAM is divided into eight pages, from PAGE0 to PAGE7, which are used for monochrome 128x64 dot matrix display, as shown in below figures. GDDRAM pages structure of SSD1309 When one data byte is written into GDDRAM, all the rows image data of the same page of the current column are filled (i.e. the whole column (8 bits) pointed by the column address pointer is filled.). Data bit D0 is written into the top row, while data...

7.5 INTERFACE TIMING CHART 7.5.1 4-Wire Serial Interface Timing Characteristics

7.5.2 IIC Serial Interface Timing Characteristics Conditions: Vdd-Vsj- 1.65V-3.3V Ta= 25°C Table 13-6 : I:C Interlace Timing Characteristics

7.5.3 8080 8bits Interface Timing Characteristics

8. POWER ON / OFF SEQUENCE & APPLICATION CIRCUIT 8.1 POWER ON / OFF SEQUENCE Power ON sequence: 1. Power ON Vdd 2. After Vdd become stable, set RES# pin LOW (logic low) for at least 3us (ti)(3) and then HIGH (logic high). 3. After set RES# pin LOW (logic low), wait for at least 3us (t2). Then Power ON Vcc,(1) 4. After Vcc become stable, send command AFh for display ON. SEG/COM will be ON after 100ms (tAF). I llt' Power ON sn|Uencr ON Vmv RES® ON Vet (Send AFh command for Duplay 1. Send command AEh for display OFF. 3. Power OFF VDD after toFF <4' (where Minimum toFF=80ms,Typical toFF=100ms) Tlw...

深圳市鸿光显示有限公司 8.2 APPLICATION CIRCUIT 8.2.1 This circuit is for 8080 8bits interface, Charge pump application. uit interface, Recommended components components： C1、C2：4.7uF/25V(Tantalum type) or VISHAY (572D475X0025A2T) 4.7uF/25V(Tantalum C3：1uF/16V(0603) Riref：1MKohm 1%(0603) Kohm

深圳市鸿光显示有限公司 8.2.2 This circuit is for 4 wire SPI interface, Charge pump application. uit interface, Recommended components components： C1、C2：4.7uF/25V(Tantalum type) or VISHAY (572D475X0025A2T) 4.7uF/25V(Tantalum C3：1uF/16V(0603) Riref：1MKohm 1%(0603) Kohm

深圳市鸿光显示有限公司 8.2.3 This circuit is for IIC interface, Charge pump application. uit ,

深圳市鸿光显示有限公司 8.2.4 DC-DC application circuit for OLED module.

深圳市鸿光显示有限公司 8.3 Initial code void Initial_ic(void) { Write_Command(0xAE); //Display Off Write_Command(0xD5); //SET DISPLAY CLOCK Write_Command(0xA0); //105HZ Write_Command(0xA8); //Select Multiplex Ratio Write_Command(0x3F); //Default => 0x3F (1/64 Duty) Write_Command(0xD3); //Setting Display Offset Write_Command(0x00); //00H Reset Write_Command(0x40); //Set Display Start Line Write_Command(0xA1); //Set Segment Re-Map Default Write_Command(0xC8); //Set COM Output Scan Direction Write_Command(0xDA); //Set COM Hardware Configuration Write_Command(0x12); //Alternative COM Pin Write_Command(0x81);...

深圳市鸿光显示有限公司 void Clear_Ram (void) { int i,j; for(i=0;i<8;i++) { Write_Command (0xb0+i); //Set Page Write_Command (0x00); //Lower Column Address Write_Command (0x10); //Higher Column Address for(j=0;j<128;j++) { data_out(0x00); } } 8.4 COMMAND TABLE Refer to IC Spec.: SSD1309

9. RELIABILITY TEST CONDITIONS Content of Reliability Test Environmental Test *** Supply voltage for OLED system =Operating voltage at 25 C 1. All measurements shall not be started until the specimens attain to temperature stability. 2. The degradation of Polarizer are ignored for item 1,3 & 5. Evaluation criteria 1. The function test is OK. 2. No observable defects. 3. Luminance: > 50% of initial value. 4. Current consumption: within ± 50% of initial value.

深圳市鸿光显示有限公司 10. EXTERNAL DIMENSION

深圳市鸿光显示有限公司 11. PACKING SPECIFICATION TBD

12. OUTGOING INSPECTION PROVISION 1. / SAMPLING METHOD MIL-STD-1916 / inspection level III / normal inspection / single sample inspection (2) Level III; Level II Major Level III ; Minor Level II