*mydirectindustry

APF- EMC test report

1 / 33 PagesView full catalog

APF- EMC test report

Product catalog summary

General Information

Equipment Under Test (EUT): Active Power Filter, Model APF-150A with supplementary models.
Power Supply: AC400V, 50Hz, 150A, 100kvar.
Manufacturer: Shenzhen Consnant Technology Co., Ltd.

Test Standards

EN IEC 61000-6-4:2019
EN IEC 61000-6-2:2019
EN 61000-4-13: 2002+A2: 2016
IEC 61000-3-11: 2017

Test Facility

Location: CCIC Southern Electronic Product Testing (Shenzhen) Co., Ltd., Shenzhen, China.
Facilities: 10m semi-anechoic area, line conducted labs.

Summary of Tests

Radiated and Conducted Disturbances
Harmonic Current Emissions
Voltage Fluctuation and Flicker
Continuous Radio Frequency Disturbance
Electrostatic Discharge (ESD)
Electrical Fast Transients (EFT)
Continuous Conducted Disturbance
Surges
Voltage Dips and Interruptions

Performance Criteria

Criteria A, B, C defined for general performance, ensuring the EUT operates as intended without degradation.

Test Equipment

Includes Spectrum Analyzer, EMI Test Receiver, LISN, Pulse Limiter, Bilog Antenna, Power Clamp, Loop Antenna.

Summary of Test Equipment
The document lists various test equipment used for immunity testing, identified by manufacturer, model number, serial number, and last calibration date, with a calibration period of one year.

Summary of Tests Conducted
Tests were conducted under several standards, including EN IEC 61000-6-4:2019 for emissions and EN IEC 61000-6-2:2019 for immunity. All tests were applicable and passed.

Radiated Disturbances
Measurement uncertainty is +4.0 dB. The test setup followed CISPR 16-2-3 procedures, with frequency ranges from 30 MHz to 1000 MHz. Results were recorded with peak and quasi-peak detectors.

Conducted Disturbances
Uncertainty is +2.4 dB. The test setup adhered to CISPR 16-2-1 procedures, with frequency ranges from 150 kHz to 30 MHz. The EUT passed with a margin indicating compliance.

Harmonic Current Emissions and Voltage Fluctuations
Tests were conducted according to EN 61000-4-13 and IEC 61000-3-11 standards. The EUT met all requirements.

Continuous Radio Frequency Disturbance
Tests were conducted with field strengths of 1V/m, 3V/m, and 10V/m. The EUT passed all tests under performance criterion A.

Electrostatic Discharge (ESD)
Tests followed EN 61000-4-2 standards, with air discharge at ±8 kV and contact discharge at ±4 kV. All tests passed with Criterion B.

Electrical Fast Transients (EFT)
Standard: EN61000-4-4: 2012/IEC 61000-4-4, Test level 3 at 2 kV. AC port passed at ±2KV.

Continuous Conducted Disturbance
Standard: EN 61000-4-6: 2014, Test level 3 at 10 V (r.m.s.), 0.15 MHz ~ 80 MHz. Passed with Criterion A.

Surge Testing
Standard: EN 61000-4-5: 2014. All tests passed with Criterion A.

Voltage Dips and Interruptions
Standard: EN 61000-4-11: 2004. Passed with Criteria B and C, with self-recovery noted after tests.

Product Labeling

CE Marking: Labels are black or white, left justified, and affixed in a conspicuous location on the EUT.

Catalog excerpts

EMC TEST REPORT For Shenzhen Consnant Technology Co., Ltd. Building B6, Junfeng Industrial Park, Yonghe Road, Fuhai Sub-District, Bao'an District, Shenzhen City, 518103 P.R.China. Test Model: APF-150A Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior written consent of Shenzhen BCT Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen BCT Technology Co., Ltd. Tel: 86-755-2947 5656 Fax: 86-755-2947 5655 http://www.bct-test.com

Open the catalog to page 1

This report shall not be reproduced except in full, without the written approval of Shenzhen BCT Technology Co., Ltd. Tel: 86-755-2947 5656 Fax: 86-755-2947 5655 http://www.bct-test.com Page 3 of 33

Open the catalog to page 3

1. GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) Client Information Applicant: Shenzhen Consnant Technology Co., Ltd. Building B6, Junfeng Industrial Park, Yonghe Road, Fuhai Sub-District, Bao'an District, Shenzhen City, 518103 P.R.China. Shenzhen Consnant Technology Co., Ltd. Building B6, Junfeng Industrial Park, Yonghe Road, Fuhai Sub-District, Bao'an District, Shenzhen City, 518103 P.R.China. General Description of E.U.T EUT Description: Trade Name: EUT Model No.: Supplementary Model: Power Supply: Active Power Filter CONSNANT APF-150A APF-30A, APF-50A, APF-75A,...

Open the catalog to page 4

1.3 Description of Test Facility The test facility is recognized, certified, or accredited by the following organizations: EMC Lab. Description: There is one 10m semi-anechoic an area test sites and two line conducted labs for final test. The Open Area Test Sites and the Line Conducted labs are constructed and calibrated to meet the FCC requirements in documents ANSI C63.4 and CISPR 22/EN 61000 requirements. Name of Firm : CCIC Southern Electronic Product Testing (Shenzhen) Co., Ltd. Site Location : Electronic Testing Building, No.43 ShaHe Road, XiLi Street, Nanshan District, Shenzhen, GuangDong,...

Open the catalog to page 5

This report shall not be reproduced except in full, without the written approval of Shenzhen BCT Technology Co., Ltd. Tel: 86-755-2947 5656 Fax: 86-755-2947 5655 http://www.bct-test.com

Open the catalog to page 6

Table 2: Test Equipment for Immunity Test This report shall not be reproduced except in full, without the written approval of Shenzhen BCT Technology Co., Ltd. Tel: 86-755-2947 5656 Fax: 86-755-2947 5655 http://www.bct-test.com

Open the catalog to page 7

For the EUT described above. Table 1: Tests Carried Out Under EN IEC 61000-6-4:2019 V Indicates that the test is applicable x Indicates that the test is not applicable Note: This product is beyond the standard requirements, so refer to EN 61000-3-2 & EN 61000-3-3, and make the evaluation test results according to the customer requirements, meeting the requirements. This report shall not be reproduced except in full, without the written approval of Shenzhen BCT Technology Co., Ltd. Tel: 86-755-2947 5656 Fax: 86-755-2947 5655 http://www.bct-test.com

Open the catalog to page 8

3.1 Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, antenna factor calibration, antenna directivity, antenna factor variation with height, antenna phase center variation, antenna factor frequency interpolation, measurement distance variation, site imperfections, mismatch (average), and system repeatability. The Treatment of Uncertainty in EMC Measurements, the best estimate of the uncertainty of a radiation emissions measurement is+4.0 dB. Note: (1) The tighter...

Open the catalog to page 9

3.5 Test Procedure Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. All data was recorded in the peak detection mode. Quasi-peak readings performed only when an emission was found to be marginal (within -10 dB^V of specification limits), and are distinguished with a "QP" in the data table. 3.6 Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain from the Amplitude reading. The basic equation is as follows: Corr....

Open the catalog to page 10

Radiated Emission Measurement No. Mk. Freq. Reading Correct Measure- Limit Margin Antenna Table Height Degree degree consent Radiated Emission Measurement Reading Correcl Measure Limit Margin Antenna Table Height Degree degree comment This report shall not be reproduced except in full, without the written approval of Shenzhen BCT Technology Co., Ltd. Tel: 86-755-2947 5656 Fax: 86-755-2947 5655 http://www.bct-test.com Page 11 of 33

Open the catalog to page 11

4.1. Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, and LISN. The Treatment of Uncertainty in EMC Measurements, the best estimate of the uncertainty of any conducted emissions measurement is +2.4 dB. 4.3. EUT Setup The setup of EUT is according with CISPR 16-2-1 measurement procedure. The specification used was the EN IEC 61000-6-4:2019 limits. The EUT was placed center and the back edge of the test table. The cables were draped along the test table and bundled...

Open the catalog to page 12

4.5. Test Procedure During the conducted emission test, the EUT power cord was connected to the auxiliary outlet of the first Artificial Mains. Maximizing procedure was performed on the six (6) highest emissions to ensure EUT compliance using all installation combination. All data was recorded in the peak detection mode. Quasi-peak and Average readings were only performed when an emission was found to be marginal (within -10 dB ^ V of specification limits). Quasi-peak readings are distinguished with a "QP". Average readings are distinguished with a "AV". 4.6. Summary of Test Results According...

Open the catalog to page 13

This report shall not be reproduced except in full, without the written approval of Shenzhen BCT Technology Co., Ltd. Tel: 86-755-2947 5656 Fax: 86-755-2947 5655 http://www.bct-test.com

Open the catalog to page 14

All Shenzhen Consnant Technology Co., Ltd. catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list