Pressure sensor operating instructions F. OUTPUT CIRCUIT WIRING DIAGRAMS 1 . D o n o t u s e c o rrosiv e o r f l a m m able g as o r l iqu i d w i t h t h is p roduc t . 2 . P l e ase u se w ithi n t h e r a t i ng p ressu r e r a n g e. D o n ot a pply p re s s u re b eyond r e c o m m ended m ax i m u m w ithst a n d p r e ssure , p e r m a nent d ama g e t o t h e p r e s sure s ens o r m a y o c c ur 3 . D o n o t d r o p, h it o r a llow e xc e s s i ve s hock . E v e n i f s w i t ch b ody a ppe a r s u n d amaged , i n t e r nal c ompon e n t s m a y b e b r oken a nd c an c a u s e m a l functi o n . 4 . T u r n p o wer o ff b efo r e c o n n ectin g w i r i n g. W rong w ir i n g o r s h o r t c ircuit w i l l d a m a ge a nd / o r c ause m al f u n c tion. 5 . D o n o t u s e i n e n v ironm e n t c o n tainin g s t e a m o r o i l v a por . 6 . T h i s p r oduct i s n ot e x p l o s ion - p roof r at e d . D o n o t u s e i n a t m osphe r e c o n t aining f l a m m a ble o r e xplos i v e g a s es. 7 . W i r ing f or p ress u r e s e nsor s hou l d a v o i d p o wer s our c e l i n e a n d h i gh v oltag e l i n e . I f u s e i n t h e s ame c irc u i t , n ois e m a y c a u s e m a lfunc t i o n . 8 . S e n sors a t e nd - o f - l ife m ust b e d isp o s e d o f i n a c c ordan c e w i t h E - W a s t e r e g ulati o n s o f t h e c ountr y / r eg i o n , N O T d ispos e d o f w i t h r e g ular g arb a g e . H. ADVANCE SETTING MODE Measure mode For your safety , please read the following before using Unit:mm Vacuum pressure Withstand pressure Compound pressure Filtered air, Non-corrosive/Non-flammable gas 12~24VDC±10% Ripple(P-P)≤ 10 % Current consumption Measure mode button for more than 3 seconds. Max.Load Impedance: 300Ωat power supply of 12 V, 600 Ω at power supply of 24 V Min.LoadImpedance:50Ω Indicator accuracy One point set mode H yst e resi s v al u e i s a dju s ta b le w it h in 1 ~8 d ig i ts Hysteresis mode Temperature characteristic Ambient humidity range OUT2 Operating mode setting OFF mode (Ops) One point Set mode Withstand voltage Insulation resistance Port size Response time setting Analog Output (White) (4~20mA) OUT1 (Black) Analog Output (White) (4~20mA) Display fine adjustment mode Use the or button to select to display fine adjustment mode Display color setting Press ON:Red ON:White OFF:White OFF:Red button ≥ 3 seconds to exit 2 Color Main Di s pl a y Setting M ode Sub-display Sectio n ( ) Bu t to n ( ) Button Sett ing B utton Restore factorysetting Use the or button to select to restore to default factory setting Basic function RS 485 MODBUS Pressure Unit Display S ection Functional type： L Support Z Support Panel Mounting , Turn on power saving mode or button to select button ≥ 3 seconds to exit output output+Analog output output+Analog output+Analog output output+Analog output output+Analog output+Analog Product name：Pressure Sensor Output Specifications C : Compound(-100.0 ~ 100.0KPa) V : Vacuum( 0~ -100.0KPa) P : Positive (-0.100 ~ 1.000MPa) M : Micro(-10 ~ 10KPa) Support customization…. Pressure Range ： Window comparator mode Total amplitude 1.5mm or10G, 10Hz~150Hz~10 HZ scan for 1 minute,2 hours each direction of X,Y and Z Hysteresis mode Storage temp.range Output 2 Ind ic ator Output 1 Ind ic ator Loc k I nd ica t or or button to select button ≥ 3 seconds to exit Ambient temp.range Display color selection R epe a t abi lit y Switch on indicator Window comparator mode Analog output (Current output) or button to select button ≥ 3 seconds to exit *Applicable for one point set mode and window comparator mode *Hysteresis mode does not have this setting selection (Ops) Hysteresis Window O n e po i n t m o d e comparator mode S e t mo d e Use the or bu t t o n to se l e c t Press button ≥ 3 se c o n d s to ex i t Analog output (Voltage output) OUT1 Operating mode setting NPN: open collector outputs PNP: open collector outputs Max. Load Current: 200mA Max.LoadCurrent:200mA Residual Voltage:≤1V Residual Voltage:≤1V Fixed hysteresis value Selection button for more than 5 seconds Power supply voltage E. INITIAL SETTING MODE Positive pressure Rated pressure range button ≥ 3 seconds to exit G.POWER-SAVE MODE During Power-Save mode, the main display will turned off if no buttons is pressed after 30 seconds. During Power-Save mode, the output LCD may not be synchronize with the output.It is normal and will not affect output operation. Press any button to turn-on main display temporarily. Unit setting No button operation for 30 seconds Press any button U s e the or b u t t o n to select Press button≥ 3 seconds to ex i t Measure mode Power-Save mode(Main display is of f , su b - d i s p l a y wi l l fl a s h " S L P" *1.This setting mode will not display when output spec. is OUT 1 *2.This setting mode will not display when output 2 is set to oFF *3.Pressure unit is MPa with positive pressure. Pressure uni

I PRESSURE SETTING MODE(2 OUT) Setting Condition 1: OUT 1 mode setting :" OUT 2 mode setting :" "(One point set mode) "(Not used) Measure mode: J PRESSURE SETTING MODE(1 OUT) Setting Condition 2: OUT 1 mode setting :" OUT 2 mode setting :" "(One point set mode) "(One point set mode) Altemately displayed Setting Condition 1: OUT 1 mode setting :" "(Hysteresis mode) "(Window comparator mode) Measure mode Measure mode: Altemately displayed Altemately displayed R OPTIONAL PARTS DIMENSIONSION Measure mode: Measure mode: N PEAK/POTTOM HOLD FUNCTION Altemately displayed button for more than 2 seconds...