Catalogs >
Shelco Filters >
MicroVantage WGAS Series Water Grade

MicroVantage WGAS Series Water Grade
2Pages

Catalog excerpts

MicroVantage WGAS Series Water Grade - 1

MicroVantage™ WGAS Series Water Grade Polyethersulfone Membrane Filter Cartridges • Absolute retention ratings from 0.3 to 1.0 microns • 6.0 square feet (0.56 m2) of media surface area per ten inch length for optimal performance • Cost effective absolute filtration for less critical applications not integrity tested • 100% polypropylene construction offers wide range of chemical compatibility • Rigid, molded cage protects pleated media and strengthens structural stability • Manufactured in state-of-the-art white room environment for high purity • Complies with Food & Drug Administration’s CFR criteria for food & beverage contact • Meets USP Class VI Biological Test for plastics. • Available in common end cap configurations to fit most filter housings • Produced in standard lengths up to 40 inches Applications RO Pre/Post Filtration DI Water Plating Solutions Specialty Chemicals Water & Wastewater Food & Beverage Bottled Water Microelectronics Process Water Cosmetics Specifications & Operating Parameters Pore Sizes 0.03, 0.1, 0.2, 0.45, 0.65, 1.0 microns absolute retention Nominal Lengths 9.75" (24.7 cm), 10" (25.4 cm), 20" (50.8 cm), Maximum Operating Temperature 176˚F ( 80˚C) Recommended Change-out Differential Pressure 30" (76.2 cm), 40" (101.6 cm) 35 psid (2.4 bar) Outside Diameter 2.67" (6.78 cm) Maximum Differential (Collapse) Pressure Inside Diameter 1.0" (2.54 cm) 75 psid @ 70˚F (5.2 bar @ 21˚C), 40 psid @176˚F (2.8 bar @ 80˚C) Media Surface Area 6.0 sq.ft. (0.56 m2) Sanitization and Sterilization per 10 inches filter length Gaskets/O-rings Silicone, Buna N, EPR, Viton, Teflon Encapsulated Viton (O-rings only) Materials of Construction Filter Media: Outer Cage Inner Core: End caps: Asymmetric Polyethersulfone Polypropylene Polypropylene Polypropylene Hot water at 175˚F (80˚C) at 5 psid for 30 minutes In-line steam at 257˚F (125˚C) @ 1 psid (0.7 bar) for 30 minutes Autoclavable at 257˚F (125˚C) for 30 minutes FDA and USP Compliance All materials comply with the requirements of Food and Drug Administration Title 21 of The Code of Federal Regulations 174.5, 177.1520 and 177.1630. All components meet current USP Class VI biological tests for plastics www.shelco.com

Open the catalog to page 1

MicroVantage WGAS Series Water Grade - 2

Flow vs. Pressure Drop WGAS SERIES PSI 4 .21 3 .14 2 .07 1 .00 DIFFERENTIAL PRESSURE BAR .28 0 0.03 µm 0.1 µm 0.2 µm .45 µm .65 µm 1.0 µm 0 0 2 3.791 4 7.57 6 11.36 18.93 8 GPM 37.91 LPM Gallons per Minute This chart represents typical water flow per 10" cartridge length. The test fluid is water at ambient temperature. Extrapolation for multiple elements tends to be linear, but as flows increase the P of the housing becomes more apparent. Ordering Guide (Example: WGAS0.2-10S4S) WGAS 0.2 10 S4 S PRODUCT CODE MICRON LENGTH END CAP CONFIGURATION GASKET / O-RING WGAS 0.03 0.1 0.2 0.45 0.65 1.0...

Open the catalog to page 2