Catalogs >
Shelco Filters >
MicroVantage MAS Series - General Grade

MicroVantage MAS Series - General Grade
2Pages

Catalog excerpts

MicroVantage MAS Series - General Grade - 1

MicroVantage™ MAS-G Series General Grade Polyethersulfone Membrane Filter Cartridges • Absolute retention ratings from 0.03 to 1.2 microns • 7.2 square feet (0.67 m2) of media surface area per ten inch length for high throughput and longer service life • Fully integrity tested to ensure reliable performance in critical applications • 100% flushed with 18 megohm DI water for low extractables • Manufactured in a Class 10,000 Clean Room environment for high purity • Polypropylene hardware offers wide range of chemical compatibility • Rigid, molded cage protects pleated media and strengthens structural stability • Complies with Food & Drug Administration’s CFR criteria for food & beverage contact • Meets USP Class VI Biological Test for plastics • Available in standard lengths and end cap configurations to fit most filter housings • Produced up to 40 inches in length (10 inch modules) Applications RO Pre/Post Filtration DI Water Plating Solutions Specialty Chemicals Water & Wastewater Specifications & Operating Parameters Food & Beverage Bottled Water Microelectronics Process Water Cosmetics Pore Sizes 0.03, 0.1, 0.2, 0.45, 0.65, 0.8, 1.0 and 1.2 microns absolute retention Maximum Operating Temperature 176°F ( 80°C) Nominal Lengths 9.75" (24.7 cm), 10" (25.4 cm), 20" (50.8 cm), 35 psid (2.4 bar) 30" (76.2 cm), 40" (101.6 cm) Outside Diameter 2.67" (6.78 cm) Inside Diameter 1.0" (2.54 cm) Recommended Change-out Differential Pressure Maximum Differential (Collapse) Pressure 75 psid @ 70ºF (5.2 bar @21ºC), 40 psid @176ºF (2.8 bar @ 80ºC) Sanitization and Sterilization Hot water at 175ºF (80ºC) at 5 psid for 30 minutes Media Surface Area 7.2 sq.ft. (0.67 m2) per 10 inches filter length In-line steam at 257ºF (125ºC) @ 1 psid (0.7 bar) for 30 minutes Autoclavable at 257ºF (125ºC) for 30 minutes Gaskets/O-rings Silicone, Buna N, EPR, Viton, Teflon Encapsulated Viton FDA and USP Compliance (O-rings only) Materials of Construction Filter Media: Outer Cage Inner Core: End caps: Asymmetric Polyethersulfone Polypropylene Polypropylene Polypropylene All polypropylene materials comply with the requirements of Food and Drug Administration Title 21 of The Code of Federal Regulations 174.5, 177.1520 and 177.1630. All components meet current USP Class VI biological tests for plastics www.shelco.com

Open the catalog to page 1

MicroVantage MAS Series - General Grade - 2

Flow vs. Pressure Drop Integrity Testing This chart represents the typical water flow per 10" cartridge length. Cartridges are tested in water at ambient temperature. Data may be extrapolated for multiple lengths, but as flow rate increases, AP of the housing becomes more apparent. GRADE OPTION Ordering Guide (Example: MAS0.2-10S4S-G) f High Temperature construction (cage, core, end caps): Maximum Temperature 200°F (93.3°C) - Available only in 222 or 226 with Fin or Flat end caps. Filter Housings Shelco manufactures a full line of filter housings. From our rugged single cartridge housings...

Open the catalog to page 2