Catalogs >
Shelco Filters >
MicroVantage MAS Series - Beverage Grade

MicroVantage MAS Series - Beverage Grade
2Pages

Catalog excerpts

MicroVantage MAS Series - Beverage Grade - 1

MicroVantage™ MAS-B Series Beverage Grade Polyethersulfone Membrane Filter Cartridges • Absolute retention ratings from 0.1 to1.2 microns • 7.2 square feet (0.67 m2) of media surface area per ten inch length for optimal performance • Fully integrity tested to ensure reliable performance in critical applications • 100% flushed with 18 megohm DI water for low extractables • Rigid, molded cage protects pleated media and strengthens structural stability • Manufactured in a Class 10,000 Clean Room environment for high purity • Complies with Food & Drug Administration’s CFR criteria for food & beverage contact • Meets USP Class VI Biological Test for plastics • Available in standard lengths and end cap configurations to fit most filter housings • Produced up to 40 inches in length (10 inch modules) Applications Food & Beverage Malt Beverages Beer RO Pre/Post Filtration Wine Bottled Water Process Water Water & Wastewater Specifications & Operating Parameters Pore Sizes 0.1, 0.2, 0.45, 0.65, 0.8, 1.0, 1.2 microns absolute retention Maximum Operating Temperature 176°F ( 80°C) Nominal Lengths 9.75” (24.7 cm), 10” (25.4 cm), 20” (50.8 cm), 30” (76.2 cm), 40” (101.6 cm) Recommended Change-out Differential Pressure Outside Diameter 2.67” (6.78 cm) Maximum Differential (Collapse) Pressure 35 psid (2.4 bar) 75 psid @ 70°F (5.2 bar @21°C), 40 psid @176°F (2.8 bar @ 80°C) Inside Diameter 1.0” (2.54 cm) Sanitization and Sterilization Media Surface Area 7.2 sq.ft. (0.67 m2) Hot water at 175°F (80°C) at 5 psid for 30 minutes In-line steam at 257°F (125°C) @ 1 psid (0.7 bar) for 30 minutes Autoclavable at 257°F (125°C) for 30 minutes per 10 inches filter length Gaskets/O-rings Silicone, Buna N, EPR, Viton, Teflon Encapsulated Viton (O-rings only) Materials of Construction Filter Media: Outer Cage Inner Core: End caps: Polyethersulfone Polypropylene Polypropylene Polypropylene FDA and USP Compliance All filters are manufactured of virgin polypropylene materials with no additives or other manufacturing agents. All polypropylene materials comply with the requirements of Food and Drug Administration Title 21 of The Code of Federal Regulations 174.5, 177.1520 and 177.1630. All components meet current USP Class VI biological tests for plastics www.shelco.com

Open the catalog to page 1

MicroVantage MAS Series - Beverage Grade - 2

Flow vs. Pressure Drop Integrity Testing PSI 3 0.1 µm 0.2 µm PORE SIZE 1.5 0.45 µm 1 0.65 µm 0.8 µm 1.0 µm 1.2 µm 0.1 μm 0.2 μm 0.45 μm 0.65 μm 0.8 μm 1.0 μm 1.2 μm AIR DIFFUSION RATE DIFFERENTIAL PRESSURE 2.5 2 Per 10" length water wetted membrane 0.5 0 ≤30cc/min@48psi ≤30cc/min@35psi ≤30cc/min@20psi ≤30cc/min@15psi ≤30cc/min@12psi ≤30cc/min@8psi ≤30cc/min@7psi 0 2 4 6 8 10 GPM GALLONS PER MINUTE This chart represents the typical water flow per 10” cartridge length. Cartridges are tested in water at ambient temperature. Data may be extrapolated for multiple lengths, but as flow rate...

Open the catalog to page 2