Catalogs >
Shelco Filters >
MicroVantage MAN Series Nylon 6.6 Membrane

MicroVantage MAN Series Nylon 6.6 Membrane
2Pages

Catalog excerpts

MicroVantage MAN Series Nylon 6.6 Membrane - 1

MicroVantage™ MAN Series Nylon 66 Membrane Filter Cartridges • Absolute retention ratings from 0.1 to 0.65 microns • Nylon 66 membranes provide electropositive charge to enhance particle removal through electrokinetic adsorption • 7.2 square feet (0.67 m2) of media surface area per ten inch length for optimal performance • MAN grade cartridges are flushed and dried to ensure reliable performance in critical applications • Rigid, molded polypropylene cage protects pleated media and strengthens structural stability • Manufactured in a state-of-the-art white room and Class 10,000 clean room for high purity • Complies with Food & Drug Administration’s CFR criteria for food & beverage contact • Meets USP Class VI Biological Test for plastics. • Available in standard lengths and end cap configurations to fit most filter housings • Produced up to 40 inches in length (10 inch modules) Applications RO Pre/Post Filtration DI Water Plating Solutions Specialty Chemicals Water & Wastewater Specifications & Operating Parameters Food & Beverage Bottled Water Microelectronics Process Water Cosmetics Pore Sizes 0.1, 0.2, 0.45, 0.65 microns absolute retention Maximum Operating Temperature 176°F ( 80°C) Nominal Lengths 9.75" (24.7 cm), 10" (25.4 cm), 20" (50.8 cm), 30" (76.2 cm), 40" (101.6 cm) Recommended Change-out Differential Pressure Outside Diameter 2.67" (6.78 cm) Maximum Differential (Collapse) Pressure 35 psid (2.4 bar) 75 psid @ 70°F (5.2 bar @21°C), 40 psid @176°F (2.8 bar @ 80°C) Inside Diameter 1.0" (2.54 cm) Sanitization and Sterilization Media Surface Area 7.2 sq.ft. (0.67 m2) Hot water at 175°F (80°C) at 5 psid for 30 minutes In-line steam at 257°F (125°C) @ 1 psid (0.7 bar) for 30 minutes Autoclavable at 257°F (125°C) for 30 minutes per 10 inches filter length Gaskets/O-rings Silicone, Buna N, EPR, Viton, Teflon Encapsulated Viton (O-rings only) Materials of Construction Filter Media: Outer Cage Inner Core: End caps: Nylon 66 Polypropylene Polypropylene Polypropylene FDA and USP Compliance All filters are manufactured of virgin polypropylene materials with no additives or other manufacturing agents. All polypropylene materials comply with the requirements of Food and Drug Administration Title 21 of The Code of Federal Regulations 174.5, 177.1520 and 177.1630. All components meet current USP Class VI biological tests for plastics www.shelco.com

Open the catalog to page 1

MicroVantage MAN Series Nylon 6.6 Membrane - 2

Flow vs. Pressure Drop This chart represents the typical waterflow per 10" cartridge length. Cartridges are tested in water at ambient temperature. Data may be extrapolated for multiple lengths, but as flow rate increases, AP of the housing becomes more apparent. Ordering Guide (Example: MAN0.2-10S4S-E} * High Temperature construction (cage, core, end caps): Maximum Temperature 200°F (93.3°C) - Available only in 222 or 226 with Fin or Flat end caps. Filter Housings Shelco manufactures a full line of filter housings. From our rugged single cartridge housings to our heavy duty multi-cartridge...

Open the catalog to page 2