ZCT2XXJ-XXX-17 series inclinometer specification I,General Description ZCT2XXJ-XXX-17 is a low cost two-axis tilt sensor which is developed and produced by Shanghai ZC sensor. Its measuring range is ±60 degrees in maximum. has zero setting function as well as optional Baud rate and so on. •Small size and light weight. •Angle measuring，leveling adjustment， •Be waterproof and dustproof with aluminium shell. zero setting. •Stable and reliable performance. •Mining machine and petroleum drilling •Cost effective and ease of integration. •Aloft work platform monitoring. Support +5V or 7-15V power supply (note in •Security control ， monitoring ， alarm order) system. •Angular measurement of arm ， dam ， construction，bridge. •Aligning control，bending control. IV. Part number introduction ZCT 2 XXX J- X Power supply, e.g.: Q express 5V supply, R express 7~15V supply Interface type, e.g.: T express TTL output, A express RS232 Housing, e.g.: N express without housing, L express with aluminium housing Measuring range, e.g.: 360 express 360 degree，45 express 45 degree Number of axis, e.g.: 1 express one axis，2 express two axis. V. Technical Specification（Unless otherwise specified, the following parameters were Shanghai zhichuan Electronic Tech Co.,Ltd Add: 3/F building, No.1128 Denghui Road, Minhang, Shanghai, China,201109 Tel: 021-64908096 Fax

| OBCillWtt VHHP tiwinmiTWi Document NO.: WI-JS-358-006 measured at room temperature 25°C) Shanghai zhichuan Electronic Tech Co.,Ltd - 2 - Add: 3/F building, No.1128 Denghui Road, Minhang, Shanghai, China,201109 Tel: 021-64908096 Fax: 021-64906992 email:[email protected]

| OBCillWtt VHHP tiwinmiTWi Document NO.: WI-JS-358-006 If current x-axis angle value is +12.5 degree and Y-axis is -7.3 degree, it display as follows X+12.5(20)(20) Y-07.3(0D)(0A) Axis direction angle space space axis direction angle enter newline Note : 88.8 is displayed when over range 2.Hex Format Output each group of data has five bytes, the first two byte is X axis angle data, the second two byte is Y axis angle data, the last byte is 0x0A. If the first byte of angle data is 1, represent X axis.If it is 0, represent Y axis. Secondary byte is sign bit.0 is positive,1 is minus. The others...

| OBCillWtt VHHP tiwinmiTWi Document NO.: WI-JS-358-006 Communication command Note: Shanghai zhichuan Electronic Tech Co.,Ltd - 4 - Add: 3/F building, No.1128 Denghui Road, Minhang, Shanghai, China,201109 Tel: 021-64908096 Fax: 021-64906992 email:[email protected]

IjjjjRj euiims Document NO.: WI-JS-358-006 l.System will output version number after power on. 2. When power on, system will enter'' output angle value'' status, output format is same as last time power off,(Continuous output is the defaulted output mode.) 3.when customer want to set ''Single data output'', must enter ''Set data group ''@??'' command at first, then set the single output data group. VII. Installation and user instruction (unit:mm) 1, PCB board installing size and definition of wire connection Shanghai zhichuan Electronic Tech Co.,Ltd - 5 - Add: 3/F building, No.1128 Denghui Road,...

| OBCillWtt VHHP tiwinmiTWi Document NO.: WI-JS-358-006 2, Installation attention Incorrect installment will lead to a big tolerance on the measured angle. Make sure the correct installation of 'two planes' and 'two lines',please pay attention to the following two points: ©: 'two planes' means mounting surface of the sensor should entirely be close to the mounting surface of the measured objects(the mounting surface of the measured objects should be horizontal as possible as it can). Angle is not allowed(eg: angle a in diagram A). Correct installation method refers to diagram B. ©:'two lines'...

Actual installation Ideal installation Include angle is not allowed Sensor Measured plane Measured plane Measured plane Axie of Measured paralle VIII Order information: All related part number is as below: ZCT245J-NTQ-17 Specification subject to change without notice! Shanghai zhichuan Electronic Tech Co.,Ltd Add: 3/F building, No.1128 Denghui Road, Minhang, Shanghai, China,201109 Tel: 021-64908096 Fax：021-64906992 email:[email protected]