Catalogs >
Shanghai Zhichuan Electronic Tech Co., Ltd >
ZCT190AL-V1

ZCT190AL-V1
5Pages

Catalog excerpts

ZCT190AL-V series 1-axis tilt switch specification General description: ZCT190AL-V series are 1-axis tilt switches which researched and produced by Shanghai Zhichuan. Measuring range is from 0 to 90 degrees. Output through serial port RS232. Operating point of the switch can be set. They are widely used in construction and machinery fields. Features: Industrial devices entirely Stable and reliable performance Shockproof greater than 10000g Wide supply allowed reverse power protection cast aluminum housing with IP65 protection grade CE certification Crane Hoist Aerial work vehicles and elevator Security control, monitoring, alarm Technical specification: item Supply voltage Quiescent current Measuring range Zero temperature drift Response time(3 Operating temperature Size of housing Remark 1: quiescent current refers to the operating current when the supply is 12V and there is no alarm signal outputting. Shanghai Zhichuan Electronic Tech Co.,Ltd ADD：3/F,1128 Denghui Rd., Minhang district, Shanghai, 201109,China. TEL：+86-02

Open the catalog to page 1

Remark 2: accuracy is the RMS error value of the measuring angle and true angle in many times(≥16 times) Remark 3: from the time when the input angle reaches to the set angle to the time when the device outputs alarm signal, the time difference is the response time. Wire definition and using instruction: 1. Internal structure and external wire connection: Running process and work conditions: 1) after power on, if the tilt angle of the measuring axis is not in the alarm rang, the relay switch off and the alarm signal is off, then the green lamp lights. If the tilt angle of the measuring axis...

Open the catalog to page 2

should be less than 40V. 4. Note: short the 7th pin with the ground for 2 seconds, can be realized function of command“&Z”; short for 10 seconds, can be realized the function of command “&R”. If this function is not used, please avoid the 7th pin to connect with ground and other pins and you can cut off the pin. Digital output of angle: 1. RS232 serial port communication protocol setting: Baud rate:9600, start bit:1bit, data bit:8 bits, stop bit: 1 bit, parity bit:none. 2. Output form of angle（ASCII code）： Output one set of 9 bytes; Byte1：X Byte6：decimal point“.” Byte2： = Byte7： digit...

Open the catalog to page 3

2. *n――sending data command 3. &Z ――set the current position as the relative zero, store the related data in EEPROM, and output the relative angle. Output “SZ” when receive command.(eg: if the current angle is 5 degrees, set this angle as relative zero. When the measurement angle is 90 degrees, the actual output angle is 85 degrees). 4. &R ――output the absolute angle (cancel relative zero setting), output “SR” when receive command. The green lamp will shine 3 times after successfully set. 5. RA ――read the set alarm angle, the angle range is “000.0～090.0”, defaulted value is 070.0, it is 70...

Open the catalog to page 4

Tilt switch location at zero degree： tilt sensor location at 90 degree 1-axis tilt switch 1-axis tilt switch Order information： part No ZCT190AL-V1 （alarm when reach the alarm angle） Part No ZCT190AL-V2（delay 1s to alarm when reach the alarm angle） Specification subject to change without notice! Shanghai Zhichuan Electronic Tech Co.,Ltd ADD：3/F,1128 Denghui Rd., Minhang district, Shanghai, 201109,China. TEL：+86-021-64908096 Http://www.zc-

Open the catalog to page 5

ZCT190AL-V1 5Pages

Catalog excerpts

All Shanghai Zhichuan Electronic Tech Co. catalogs and technical brochures

ZCT190AL-V1
5Pages