Catalogs >
Shanghai Zhichuan Electronic Tech Co., Ltd >
ZCT-CX01-C Inclinometer with remote display For Pipe Jacking Machine

ZCT-CX01-C Inclinometer with remote display For Pipe Jacking Machine
7Pages

Catalog excerpts

ZCT-CX01-C Inclinometer with remote display For Pipe Jacking Machine - 1

ZCT-CX01-C introduction General description: ZCT-CX01-C is applied in pipe jacking machine. It is high accuracy, stable performance and anti-shake. It is ableto output signal of 2-axis. Range is ±10 degrees Funtions description: 1. display: display the angle information of which connects with the displayer currently and the current output mode(absolute/related output) of the sensor.(ZCT-CX01-C special sensor) 2. control: set the absolute zero of the sensor and shift from absolute/related angle output. Remark 1: resolution meas the smallest angular increment at which a detectable change in output can be measured. Remark 2: display error means the difference between diplayed value and the corrosponding true input value. Remark 3: response time means the needed time of the sensor when sensor’s output reaches the 85% of the max output which is caused by the step change of the measured Shanghai Zhichuan Electronic Tech Co., Ltd. -1-

Open the catalog to page 1

ZCT-CX01-C Inclinometer with remote display For Pipe Jacking Machine - 2

tilt angle. 9 Shanghai Zhichuan Electronic Tech 1. power cable: provide supply for ZCT-CX01-C (8～36V) 2. LED display screen of X axis:display the angle information of X axis which is measured by inclinometer ZCT-CX01-C. 3. LED display screen of Y axis:display the angle information of Y axis which is measured by inclinometer ZCT-CX01-C. 4. Zero calibration button: set absolute zero position of the connected inclinomter ZCT-CX01-C. 5. Cable connected with the probe: connect with the inclinometer 6. Mounting hole: to fix ZCT-CX01-C 7. Indicated lamp of absolute output: indicate the absolute...

Open the catalog to page 2

ZCT-CX01-C Inclinometer with remote display For Pipe Jacking Machine - 3

1. When power on, the two LED digital tube display 8888 8888. If the tilt sensor is connected with the display, after about 2 seconds, the two digital tube will respectly display the angle value of X and Y axis, and the corresponding idicated lamp lights. If sensor is not connected, 8888 8888 will be displayed all time and the indicated lamp will not light. 2. This system supports hot swap. In power state, unplug the sensor, after about 2 seconds, system comes into the state without sensor, 8888 8888 is displayed and the corresponding lamp is off. In power state, plug the sensor, angle...

Open the catalog to page 3

ZCT-CX01-C Inclinometer with remote display For Pipe Jacking Machine - 4

Housing size and connecting definication: unit：mm Housing size: legnth*width*hight＝150*126*35（mm） Power cable connecting red——8～36V black——GND displayer connecting wire： PIN1——8～36V PIN2——GND PIN3——TX PIN4——RX PIN5——NC Size of tilt sensor： Shanghai Zhichuan Electronic Tech Co., Ltd. Address: 3F compositive Building, No.1128Denghui Road, Minhang, Shanghai, China. Tel：86 21 6490 8093 Ext.214; Fax: 86 21

Open the catalog to page 4

ZCT-CX01-C Inclinometer with remote display For Pipe Jacking Machine - 5

Shanghai Zhichuan Electronic Tech Co., Ltd. Address: 3F compositive Building, No.1128Denghui Road, Minhang, Shanghai, China. Tel：86 21 6490 8093 Ext.214; Fax: 86 21 6490 6992; Email:s

Open the catalog to page 5

ZCT-CX01-C Inclinometer with remote display For Pipe Jacking Machine - 6

Tilt sensor Connected cable Physical picture picture： Shanghai Zhichuan Electronic Tech Co., Ltd. Address: 3F compositive Building, No.1128Denghui Road, Minhang, Shanghai, China. Tel：86 21 6490 8093 Ext.214; Fax: 86 21 6490 6992; Email:sales@zc-sensor.com;

Open the catalog to page 6

ZCT-CX01-C Inclinometer with remote display For Pipe Jacking Machine - 7

Order information：part No. ZCT-CX01-C Accessories connect cable both ends FQ14-5T-6/5ZP-6( apart from flanch )connector Accessories： cable（ connector） Length customize customize。 Specifications subject to change without notice! Shanghai Zhichuan Electronic Tech Co., Ltd. Address: 3F compositive Building, No.1128Denghui Road, Minhang, Shanghai, China. Tel：86 21 6490 8093 Ext.214; Fax: 86 21 6490 6992; Email:sales@zc-sensor.c

Open the catalog to page 7