Catalogs >
Shanghai Zhichuan Electronic Tech Co., Ltd >
ZC ZCT245J-LAS-1L-140 2 Axis Crane inclinometer Switch

ZC ZCT245J-LAS-1L-140 2 Axis Crane inclinometer Switch
7Pages

Catalog excerpts

ZC ZCT245J-LAS-1L-140 2 Axis Crane inclinometer Switch - 1

I. Overview ZCT245J-LAS-1L-140 is a dual axis tilt switch developed and produced by Shanghai Zhichuan Electronic Technology Co., Ltd. The measurement range is ± 45 ° for two axes. The switch operating point and trigger delay time can be customized. It is widely used in engineering machinery industry. II. Product Feature All industrial devices are used, with stable and reliable performance Impact resistance greater than 10000g Powered by DC 8 ~ 30V, with reverse polarity protection Using cast aluminum housing, protection grade IP65 IV.Technical Parameters ( Unless otherwise spe III. Product Application Aerial Work Vehicles and Lifts Crane, hoist Automatic positioning platform Security control, monitoring, alarm applications fied, the following parameters are typical values at room temperature (25 °C)); Working Parameters :

Open the catalog to page 1

ZC ZCT245J-LAS-1L-140 2 Axis Crane inclinometer Switch - 2

www.zc-sensor.com Zero point temperature drift Performance Parameters: Item Note 1 : It is recommended to use DC 12V power supply in order to reduce the internal loss of the device. When the power supply voltage is greater than 30V, it may cause damage to the device or shorten its life. Note 2 : Static working current refers to the working current of the device when the alarm is triggered under a power supply voltage of 12V. Note 3:Load current refers to the current flowing when the relay circuit is closed. V. Wiring Definition and Instructions : 1. Wiring Definition and diagram of wiring :

Open the catalog to page 2

ZC ZCT245J-LAS-1L-140 2 Axis Crane inclinometer Switch - 3

2. The product leads the common end and constant open end of the relay. After the product is powered on, when the all of the tilt angles of the four semi-axes of the device are less than the set alarm angle, the internal relay of the product is closed. When the device tilt angle is greater than or equal to the set alarm angle (factory set values are X + 13 degrees, X-13 degrees, Y + 35 degrees, Y-25 degrees), the internal relay is open. -3-

Open the catalog to page 3

ZC ZCT245J-LAS-1L-140 2 Axis Crane inclinometer Switch - 4

www.zc-sensor.com _A/2 3. The RS232 communication interface pin is reserved in the product to set the switch alarm angle and alarm delay time. 4. When it is smaller than the alarm angle, the green light is on; when it is larger than the alarm angle, the red light is on. VI. Digital output of angle: (Note: In order to set the tilt switch with other RS232 communication equipment, user need to open the case and connect the RS232 communication interface inside.) 1. Setting of the serial interface of RS232: Baud rate: 9600bps, start bit: 1 bit, data bit: 8 bits, stop bit: 1 bit, check bit: None....

Open the catalog to page 4

ZC ZCT245J-LAS-1L-140 2 Axis Crane inclinometer Switch - 5

After sending * COMMAND to enable the command response mode and angle output, you can send the $$ command pause the angle output to better view the product's response to the command. Send the * COMMAND again to resume the angle output. 3. &Z ――Set the current position as relative zero, store related data in EEPROM, and output relative angle. After receiving the instruction, respond: "Setting relative zero". &R ――Output in absolute angle, and respond after receiving the command: "Absolute zero". *SetxP=???――Set the alarm point of the positive axis of the X axis. "???" is an angle value that...

Open the catalog to page 5

ZC ZCT245J-LAS-1L-140 2 Axis Crane inclinometer Switch - 6

VIII. Product installation and wiring size chart: 1. Size drawing with mounting plate (unit：mm) 2. Size drawing with mounting plate (unit：mm) 上海直川电子科技有限公司地址：上海市闵行区灯

Open the catalog to page 6

ZC ZCT245J-LAS-1L-140 2 Axis Crane inclinometer Switch - 7

Ordering instructions: Product model ZCT245J-LAS-1L-140 Optional components: mounting plate AZB-04 (4 countersunk head screws M4 * 12) 上海直川电子科技有限公司地址：上海市闵行区灯辉

Open the catalog to page 7