Catalog excerpts
ShanghaiZhichuan Electronic Tech Co., Ltd. ZCT1360K-LBS-ALV-H6-77 INCLINOMETER USER MANUAL
Open the catalog to page 1
Contents I.Overview II.Product Feature IV.Spec Sheet V.Communication Protocol VI.Wiring definition size VII.Installation Precautions
Open the catalog to page 2
ZCT1360K-LBS-ALV-H6-77 INCLINOMETERSPECIFICATION I.Overview With RS485 differential signal / ModBus protocol output and kilometers' transmission distance, ZCT1360K-LBS-ALV-H6-77 is a single-axis inclinometer developed and manufactured by Shanghai Zhichuan Electronic Technology Co., Ltd. for industrial field control. II. Product Feature Full measurement Range, High cost effectiveness; Compact size, light weight, easy to integrated into various systems; 100% industrial components, reliable performance; Anti-shock, anti-vibration. III. Applications Wind deviation monitoring, inclination...
Open the catalog to page 3
Ingress Level Note 1 : Resolution refers to the minimum variation that can be detected by the sensor while working in its valid range. Note2 : Response time is the time required for the sensor's output to rise to 85% due to a step change in the measured tilt angle. 3. Electromagnetic compatibility
Open the catalog to page 5
1 .The communication protocol is compatible with modbus RTU protocol, the baud rate is:
Open the catalog to page 6
R is read-only and W is write-only. The read register uses function code 03H, the write register uses function code 06H, and the read local address uses function code 42H. 2.Host read angle data command:
Open the catalog to page 7
Data analysis: The data field of the reply frame is 01H 23H 3CH 00H 1.01H is Angle data hundred digits 2. 23H is Angle data tens digits 3.3CH is Angle data Decimal Tenth/Hundred Places 4.00H is Angle data Decimal Fractional reservation 3.Set sensor address command
Open the catalog to page 8
byte byte byte byte
Open the catalog to page 9
Note: When the address signal line (TTL signal) is low (ground), the sensor will set the address to 0x01. When the signal line is high (floating), the sensor will set the address to 0x02. If the sensor receives the Set Address command (not 0x00, 0xFF), the sensor will no longer detect the level of the signal line and use the set address.
Open the catalog to page 11
VII.Installation Precautions 1. This product should be installed as shown in the installation method as shown below. The mounting surface is perpendicular to the horizontal plane.
Open the catalog to page 12
Even if the mounting surface (or running surface) is inclined at 30° from the horizontal plane, there is almost no influence on the precision output of this product, and it can be applied to an industrial site that does not meet the above installation requirements. As shown below： VIII.ZCT1360K-LBS-ALV-H6-77default cable length 1 Meter 11
Open the catalog to page 13All Shanghai Zhichuan Electronic Tech Co. catalogs and technical brochures
-
ZCT330M1-LWP-AN-YKG20 Pages
-
ZCT-CX0910 Pages
-
ZCT-CX30018 Pages
-
ZCTR044 Pages
-
ZCTXXXK-LPS-1554 Pages
-
ZCT190J-LPS-A3 Pages
-
ZCT190J-LNS-203 Pages
-
ZCT190AL-V15 Pages
-
ZCT181J-LMS3 Pages
-
ZCT1XXX-LNX-1403 Pages
-
ZCT2XXL-XXS-A-7X9 Pages
-
ZCT1XXXJ-SXX-19072 Pages
-
ZCT190J-SPS-A6 Pages
-
ZCT290RS-LPS-775 Pages
-
ZCT1000ML-S2304 Pages
-
ZCT330Ex-SWP-N-YK4 Pages
-
ZCT215L-SQS-A1B-19074 Pages
-
ZCT175J-NMQ4 Pages
-
ZCT145KR-LQS-AH-62074 Pages
-
ZCT21B0J-LPS-A4 Pages
