*mydirectindustry

Catalogs
Shanghai Zhichuan Electronic Tech Co., Ltd
ZC-LCS02D Tilting Switch Sensor for Tail gate control

ZC-LCS02D Tilting Switch Sensor for Tail gate control

Product catalog summary

General Description: The ZC-LCS02D is a single-axis tilting controller designed for industrial applications, offering stable and reliable performance with features like low-level alarm output and dual-route control terminal output signals.

Features: The device is impact-resistant up to 1000g, housed in a cast aluminum shell with an IP67 protection grade, suitable for various industrial devices.

Applications: Primarily used in industrial settings for tail gate control and other applications requiring precise tilt measurement.

Technical Parameters:

Power Supply: 10-24 V DC
Quiescent Current: 27-35 mA at 12V
Operating Temperature: -30 to +85°C
Output Drive Current: 1.5 A
Alarm Drive Current: 1 A
Measurement Range: -60° to +60°
Resolution: 0.1°
Accuracy: ±0.5° up to 45°, ±1° up to 60°
Zero Temperature Drift: ±0.0067°/°C
Response Time: 0.4 seconds
Size: 150x51x22 mm, Material: PA66

Wiring and Introduction:

5-core cable with a 5-pin socket for power and control outputs.
4-core cable for square wave output to drive LED flicker.
2-core wires for switch contacts.

Work Parameters:

5-pin connector provides alarm output with low-level and high-level states depending on the sensor angle.
4-core output provides square wave signals for LED flicker when the sensor angle is less than +60°.

Mounting and Size: The device includes a mounting diagram and specifies cable lengths: 0.35 meters for 5-core and 4-core cables, and 1 meter for 2-core cables.

Ordering Information: Part Number: ZC-LCS02D. Specifications are subject to change without notice.

Catalog excerpts

ZC-LCS02D Tilting Switch Sensor for Tail gate control-1

ZC-LCS02D incline controller manual II. Features All industrial devices are used, and the performance is stable and reliable. Impact resistance is greater than 1000g. Cast aluminum shell, protection grade IP67. I. General description ZC-LCS02D , the single axis tilting controller has the function of low level of alarm output, two route combination control terminal control output signal and so on. III. Applications Tail gate control IV. Technical parameter Parameter Note 1: quiescent current refers to the working current of the device when the supply voltage is 12V and no alarm signal is output (12V is recommended). Note 2: accuracy refers to the root mean square error of the actual real angle and the measurement angle of the sensor several times (more than 16 times). Note 3: when the input angle reaches the set angle, the time required for the device to output the alarm signal is the Shanghai Zhichuan Electronic Tech Co.,Ltd - 1 - ADD: 3/F, 1128 Denghui Rd., Minhang district, Shanghai, 201109, China. TEL: +86-021-64908096 E-mail:[email protected] Http://www.zc-sensor.com

Open the catalog to page 1

ZC-LCS02D Tilting Switch Sensor for Tail gate control-2

response time. V. Wiring and introduction 1. Internal diagram of the tilt controller ADD: 3/F,1128 Denghui Rd., Minhang district, Shanghai, 201109,China. TEL: +86-021-64908096 E-mail:[email protected] Http://www.zc-sensor.com

Open the catalog to page 2

ZC-LCS02D Tilting Switch Sensor for Tail gate control-3

Connector wiring 1) 5 pin connector’ 5 pin (5_5) alarm output low level (about 0V), drive current less than 1A, in no alarm condition, is in high impedance state (maximum leakage current 7uA). 2) 5 core connector’ 2 pin and 3 pin (5_2, 5_3) alarm output high level, drive current less than 1.5A (output voltage nearly equal to 0.5V voltage power supply voltage), in no alarm condition is in high resistance state (maximum leakage current 12uA). 3) 4 core output, alarm output is square wave, used to drive LED flicker (driving current 1A, maximum voltage is close to voltage -0.5V). 4. Work state is...

Open the catalog to page 3

ZC-LCS02D Tilting Switch Sensor for Tail gate control-4

Mount size（mm） Cable length : The 5 core connector cable is 0.35 meters , the 4 core terminal cable is 0.35, and the 2 core connector cable is 1 meters. Specifications subject to change without notice! Shanghai Zhichuan Electronic Tech Co.,Ltd ADD：3/F,1128 Denghui Rd., Minhang district, Shanghai, 201109,China. TEL：+86-021-64908096 E-mail:[email protected] Http://www.zc-sensor.com

Open the catalog to page 4

All Shanghai Zhichuan Electronic Tech Co., Ltd catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list