SSR-K 2024
3Pages

Comparison with R SerlesSaxvng more than 30% as maximunm,10% as average in eadh model. 如图 1 所示，罗茨鼓风机输送气体进入机壳和叶轮间的腔体内，因为压力的停止，从排出到吸入末端会有一定气体的 回流。K 系列风机为了防止回流已尽量减少机壳和叶轮的间隙去保证最佳的容积效率，并且采用特殊设计的叶轮、高转速 Compact Design 与原系列相比，相同口径的前提下，K 系列采用特殊的叶轮和高转速设计，实现了超过 120% 最大流量的覆盖。尽最 大可能去实现体积的最小化，同时采用了特殊设计的吸入消音器，减小了整个包装尺寸。 Specially designed impellers and high rotating speed of K achieve more than 120% of maximum capacitycompared with our previous model,SSR,with same bore.We have much possibility to supply one more smallermodel with newly designed suction silencer shortened its height to downsize the total blower package. 和节能型皮带，从而实现最高的节能。 As Fig.1 shows,rotary blower transfer the gas by progressing the cavities peween casImng ana tapeter.There is little backfiow of gas from discharge to suction end because of pressure stall.In K model , to prevent this backflow, the clearance between casing and impellers is minimized to secure the bestvolumetric efficiency. And the widest cavities by specially designed impeller, high rotating speed, andenergy-saving V-belt achieve the better energy saving. 各压力点下的流量 Qs(m*/min) 和轴功率 La(kW) Suction Volume Qs(m³/min) for each discharge pressure and required power La(kW) TYPE SSR-K PERFORMANCE TABLE Thorough Development and Design for the best energy saving! 另外设计的新型吸入消音器可减少气动噪音 ; 同时鼓风机的特殊轴结构更进一步降低了风机的噪音和振动。 Not only newly designed 3 lobe impellers, but also mechanical function of the new casing to reduce thepulsation is refined from the previous , shall reduce the pulsation while compressing gas.Moreover, newdesigned suction silencer reduce the pneumatic noise efficiently. Into the bargain , stiffer structure of blower bare shaft lead to further lower noise and vibration! Designed for Lower Noise and Vibration! Compatibility for Replacement and Easy Maintenance 对于保养得便利性体现在了驱动轴承自带润滑 , 不需要日常的检查和更换润滑油 ; 同时对于吸入消音器带有起重手柄，方便 检查和滤芯的清洗更换。详见图 2 In case of the same bore as previous model SSR, the foundation works and modification of piping will notbe required for the replacement from SSR to. Also,for your easy maintenance ,bearing lubricated by grease at pulley end installed.No check,complement,and change of the grease will be required. Also,for easy replacement of the air filter, thereare lfting handleson the filter cover In detail,please refer to Fig.2.

TYPE SSR-K PERFORMANCE TABLE 各压力点下的流量 Qs(m*/min) 和轴功率 La(kW) Suction Volume Qs(m³/min) for each discharge pressure and required power La(kW) 10kPa Qs 吸入消声器 Suction Silencer SSR-K 外形尺寸图 排出消音器（KM) Discharge Silencer (KM) 1.Unit of dimension is millimeter(mm) 2.The weight of motor is excluded in the above value. 3. Dimension E is marked according to the maximum motor. OUTLINE DIMENSIONS 排出消音器（RKM) Discharge Silencer (RKM)

BLOWER PERFORMANCE COMPARISON TABLE Vacuum Breaker (VOCP-B)