SLA-3 Bending Machine Protection Device
36Pages

SLA-3 Bending Machine Protection Device Instruction Manual SHANDONG LAIEN OPTIC-ELECTRONIC TECHNOLOGY CO.,LTD.

Contents 1 Basic Introduction 1.1 Summary ………………………………………………………………… 1 1.2 Manual Composition ………………………………………………… 1 1.3 Standards ……………………………………………………………… 1 1.4 Safety Signs Instruction 2 Important Information 2.1 Terminology……………………………………………………………… 5 2.2 Usage …………………………………………………………………… 6 2.3 Technical Parameters…………………………………………

Contents 4.4 Installation Postion …………………………………………………… 16 4.5 Installation Instruction ………………………………………………… 18 4.6 Installation Tools ……………………………………………………… 21 5 Wiring 5.1 Cautions ……………………………………………………………… 22 5.2 Wiring with Safety Relay ……………………………………………… 23 5.3 I/O Wiring ……………………………………………………………… 24 5.4 Signal Cable ……………………

1 Important Information 1.1 Summary This manual is composed of the SLA-3 device's instruction, operation, installation, wiring, maintenance and troubleshooting etc. excludes the operation instruction for the machine protected(installed with SLA-3), please refer to the manual from the machine protected manufacturer 1.2 Composition This manual contains chapters: Important information contains emphasis information,the makeup of this manual,control dependability information,certificate,directive and so on. Basic introduction contains the usage,features, working schematic drawing and...

Shears—Safety requirements Hydraulic press brakes—Safety requirements Safety of laser products--Part 1:Equipment classification,requirements and users guide Degrees of protection provided by enclosure(IP code) 1.4 Safety Signs Failure to follow the instruction may result in a serious injury or death Failure to follow the instruction may lead to minor or moderate injury 1.5 Notes 1. Read manual Please take note of the contents marked peroper operation instructions, taken as the important components for SLA-3 device, ensure of the manual placed at right place. 2. Operator Ability To carry out...

● SLA-3 offers complete protection (finger and hands) from rapid intervention shortly before the press closes completely, during the very short time before complete closing with non protection, at the same time SLA-3 function is muted(muting indicator ON) ● The switch keys should be kept by the designated person, and to select the working modes according to the application requirements ● The protection function can't be performed to the bending machine with press closing only at working speed, or too long overrun distance ● Prevent the SLA-3 device falling down 1.6 Application Cautions 1....

4. SLA-3 special mode enables the bending or wavy material or even edge bending within a closed box. If the bending machine only closes at work speed,or too big excess of stroke, SLA-3 won't provide protection, i.e. won't prevent access to the hazardous area. 5. The bending machine control system must meet type 4 standards requirements. 6. The protected machine must detect the danger status, and stop it 7. The laser beam maybe intervened by airflow, cause the unexpected lockout, so guarantee the workplace without airflow or little. 1. Must keep a certain distance between the SLA-3 beams and...

2.Basic Instruction 2.1 Terminology Electro-sensitive protective equipment (ESPE) Assembly of devices and components working together for protective tripping or presence-sensing purposes and comprising as a minimum. Detection Capability Sensing function parameter limit specified by the supplier that will cause actuation of the electro-sensitive protective equipment(ESPE). EDM: Means by which the electro-sensitive protective equipment(ESPE) monitors the state of control devices which are external to the ESPE. Lockout Condition: Condition, initiated by a fault, preventing normal operation of...

Termination of the ability of an item to perform a required function Note 1: After failure the item has a fault Note 2: "Failure" is an event, as distinguished from"fault", which is a state. Note 3: This concept, as defined, does not apply to items consisting of software only. Note 4: In practice,the term fault and failure are often used synonymously Self-checking: The device switches automatically into the "safe state" when it is faulty. Standard Mounting Range: Maximum distance between transmitter and receiver is 5 m, if exceed the distance may lead to hazardous motion. For longer range...