JGCNR26650-5000mAh-3.6VEnglish Specification
10Pages

Lithium-ion Cell Series Product Specification Product Name Lithium-ion Cell Wang Yong Company Name Signature Customer Approval Date Company stamp Shandong Goldencell Electronics Technology Co.,Ltd Headquarter Branch office (Shenzhen) Add: Room 8006, Building 1, Shenzhen Beihang Building, Yuexing 4th Road, Nanshan District, Shenzhen, Guangdong, China Tel: +86-755-28891995 Fax：+86-755-28892486 Add：Fuyuan 5 Rd. Lithium Battery Industrial Park, Hi-tech District, Zaozhuang City, Shandong Province, China Toll-free telephone：400-812-5699 Branch Office (Europe) Pihatörmä 1 A, 02240 Espoo, Finland Tel: +358 453246642 Email: tony.yang@goldencell.biz

Lithium-ion Cell Series

Lithium-ion Cell Series 1. Application Scope This product specification describes product performance indicators of Lithium-ion cell produced by Shandong Goldencell Electronics Technology Co., Ltd. 3. Appearance and Dimension Item 4. Major Technical Parameters NO. Standard Capacity Minimum Capacity Standard Voltage Alternating Internal Resistance Charge Conditions constant-current charge to 4.2V at 0.5C, constant voltage charge to stop until 0.01C m A. Discharge Cut-off Voltage Standard Discharge Current Fast Discharge Current This current is the maximum current recommended for the...

Lithium-ion Cell Series NO. Working Temperature Storage Temperature Cell Weight Short-term storage (< 3 months) Test Method discharge capacity at normal temperature After full charge, the experiment can be put on hold for 10 minutes; 0.5C discharge to 2.75V allows five repetitions. When the range of three consecutive experiments is less than 3% of the rated capacity, the experiment can be completed ahead of time and the maximum value of the test results can be obtained. Discharge performance at different temperatures After standard charging of normal batteries, it should be stored at least...

Lithium-ion Cell Series NO. Discharge performance at normal temperature different rate Charge retention at normal temperature Charge retention and capacity recovery capability at high temperature Cycle characteristic Test Method After standard charging of normal batteries, it should be placed for 10 minutes at the prescribed ambient temperature. Then discharged to 2.75V at different rates of 0.2C, 0.5C, 1C, 2C and 3C, respectively. The capacity of batteries with different discharge rates was recorded, and the temperature rise T of batteries with different discharge rates was recorded...

Lithium-ion Cell Series Thermal Cycle Static Humidity Test Method Store the cell for 48 hours at 75±2℃after standard charge, then store the cell at -20℃ for 6 hours, and at room temperature for 24 hours. Observe the batteries’ appearance. Put the cell at 40℃±5℃ and 95%RH chamber for 48h, then get it out and store it for 2h at room temperature. Observe the appearance and discharge at 0.5C to 2.5V, then test the final capacity. Standard charge. Equip it to the vibration platform, prepare the test equipment according to following vibration frequency and relevant swing, doing frequency sweeping...

Lithium-ion Cell Series  Do not use the cell in a location where static electricity and magnetic field is great, otherwise, the safety devices may be damaged, causing hidden trouble of safety.  Use the cell charger specifically when recharging.  If the cell leaks and the electrolyte gets into the eyes, do not rub the eyes, instead, rinse the eyes with clean water, and immediately seek medical attention. Otherwise, it may injure eyes.  If the cell gives off strange odor, generates heat, becomes discolored or deformed, or in any way appears abnormal during use, recharging or storage,...

Lithium-ion Cell Series Suggestions for Cell Packs 1. Selecting principle of nickel strip is often applied to the design of cell packs. Based on the working current of cell packs to make the shunt selection of nickel strip. The common nickel strip could under the current as below: Nickel Strip Type 3*0.1 4*0.1 7*0.15 8*0.15 Normal Working Current 2A 3A 7A 8A Maximum Continues Current 4A 5A 13A 15A 2. Relation between the cell packs design current and lead wires current breakdown, and principle of wires selection. Based on the working current of cell packs to make the shunt selection of...

Lithium-ion Cell Series (3) If above 120W, chargers with aluminium alloy cooling fin or cooling fan will be suggested. (4) If under 60W, chargers with plastic shell will be suggested. 5. In the process of packs structure design and production, some measures and skills could be handled to avoid cell short circuit. (1) To strengthen the positive insulation treatment of the monomer batteries, with barley paper or other high temperature resistant material. (2) Cell in the case of size allowed, should try to use batteries of the isolation. (3) Cell when working current is larger and can't use...

Lithium-ion Cell Series Amendment Records Revision Pre-change Content Post change Content Branch office (Shenzhen) Branch office (Shenzhen) Add:B905, Wuhan University Add: Room 8006, Building 1, Research Bldg., No. 2 Yue xing Shenzhen Beihang Building, 2020.01.08 Address change Rd., Hi- tech Industrial Park, Yuexing 4th Road, Nanshan Nanshan District, Shenzhen, District, Shenzhen, Guangdong, China China Add the content of customer 2020.03.26 approval and amendment Perfect the content records Branch Office (Europe) 2021.03.15 Pihatörmä 1 A, 02240 Espoo, Add new address Finland 2021.03.15...