SFT Manual positioning stage
49Pages

Product Introduction Rail trait description Stage outline & Feeding mode technical Information Inspection standard Assemblg & Installation Using caution note Crossed roller guide type-Position stage Crossed roller stages\ Aluminum alloy \ Xaxis Crossed roller stages \ Aluminum alloy \ X+Y axes Crossed roller stages \ Aluminum alloy \ Z axis Crossed roller stages \ Aluminum alloy \ X+Y axes (Thin-type) Crossed roller stages \ High load capacity \ accuracy Linear Ball stages\carbon steel \ X axis Linear Ball stages\carbon steel \ Z axis Linear Ball stoges\carbon steel \ Horizontal Z axis...

Crossed roller Linear ball Doventail type Character istic Composed of moving rails with 2 V-groove surfaces harden finish, ground precisely,and roller bearings which are connective and take turns moving in 90 degrees to meet requirement of high parallism and high flatness.In structure, V-groove and crossed roller acquire movement in high accuracy and capacity by linear transmission to act a high precision movement and load capacity performance. ^ Slide way and body is in one unit, and Gothic arc-groove ground precisely to meet requirement of high parallism and high flatness.Gothic...

Mini-Stage Outline 1 . Mini-Stage is applied for high precision or mid and heavy capacity of various production machinery,testing device, precise positioning and quantitative movement. 2. There're many kinds of mini-stages with single axis (X axis); dual axes (XY axis); Z axis; 0axis ' aaxis... 1 . Customer's requirements of precise fine tuning ; quantitative movement and able to proceed mass feed of fine tuning. 2. Coordinated customer’s precise machinery or instrument and fixed in suitable position. 3. Feeding mode diversification such as coarse moving handle / micrometer head ;...

(refer to JIS B 6191-1993) In linear motion units, geometric staight line decides positions in order from datum point to same direction, differences between length veriation in those positions and datum is as measured point, the max. difference of geometric line is called " Straightness". (refer to JIS B 6191-1993) Linear motion parts would occur slanting in transmitting, and slanting proportion would cause deflection in linear transmission. Position is decided by same direction from datum point in order, and maximum angular gap measured from horizontal direction of each position...

Inspection Standard XY Vertical value (refer to JIS B 7440-1987) Vertical value between 2 axes also for one line of geometric line in transmission datum and one in its corresponding right angle. In the other direction(Opposite), to take slanting proportion in linear transmission, reference point of X-axis stage, and geometric line of final tested position as datum axes. X-axis stage as for datum axis, maximum of parallel errors from its vertical geometric line in opposition to datum position of Y-axis stage to final texted position is called XY vertical value. Difference of datum circle and...

Installation Single axis Move upper plate back and forth, and secure the screw on the base plate and work piece with tight confirmation. Dual-axes Screw security same as single axis. Move upper plate by rotating, and take the screw through it. Proceed taking screws through base plate in order and finding matched holes at same time. Lock the stage on the work piece with tight confirmation. Other stages Considering easy installation fit for other device, threaded hole pattern is made to meet requirement of securing from upper or lower direction, and this provides more options for installation.

Using caution note About defination of moving axis and rotating axis, GMT defines as chart below. X axis, Y axis are in parallel direction: Z axis in vertical direction; Rotating around X, Y, Z axes are called a axis, (3 axis, 0 axis individually. Please operate stages in regular range of temperature as listed. Please contact GMT if products in larger range required.

Using caution note Basic declaration Diagrams of representative explanation in catalogs are sampled in SFT products series. Products compared to diagrammatic examples in same series may have some difference in shape due to different mechanism design and spes, but basic operation remark are all the same. Notice Please read notices as follows before operation, this would have SFT series performed as best motion accuracy and usage life. Operation principles 1、SFT product series are all composed of part in high accuracy , please avoid environment of extreme high temperature , extreme low...

Position stage Crossed roller guide type Specifications options Nominal dimension Material A: Aluminum alloy Y: Dual axes ZL: X axis +L bracket Platform external dimensions Feed position SZ: Side feeding with micrometer on the top SZR: Reversed side feeding with micrometer on the top YW: Super thin dual axes CR: Reversed central feeding R: Right side feeding L: Left side feeding Feeding Postion Central feeding Reversed side Feeding Side feeding Vertical side feeding Reversed Vertical side feeling Reversed Vertical side feeling Reversed Vertical side feeling

Crossed roller stages Aluminum alloy ♦ Specification Model number + Specification Model number

♦ Specification Model number ♦ Specification Model number

Crossed roller stages Aluminum alloy + Specification ♦ Micrometer unit : 0.01mm ♦ Surface treatment : Black anodized

Crossed roller stages Aluminum alloy Specification Model number Table size Travel stroke Moving Parallelism Load capacity Aluminum alloy Micrometer unit : 0.01mm Surface treatment : Black anodized Specification Model number Table size Travel stroke Moving Parallelism Load capacity Aluminum alloy Micrometer unit : 0.01mm Surface treatment : Black anodized

♦ Specification Model number + Specification Model number

Crossed roller stages Aluminum alloy Specification Model number Table size Travel stroke Moving Parallelism Load capacity Aluminum alloy Micrometer unit : 0.01mm Surface treatment : Black anodized Specification Model number Table size Travel stroke Moving Parallelism Load capacity Aluminum alloy Micrometer unit : 0.01mm Surface treatment : Black anodized