SERVOTOUGH SpectraExact 2500 - User Manual - 35 Pages

Add to MyDirectIndustry favorites
SERVOTOUGH SpectraExact 2500 - User Manual

Catalog excerpts

Please record your analyser details below

 Open the catalog to page 1

Servomex 2500 QuickStart Manual 2500 Series - Configuration and Operation

 Open the catalog to page 3

Servomex 2500 QuickStart Manual Z CAL SCAL HISTORY -1— ZERO HISTORY '— SPAN HISTORY CHKZ&S -1— CHECK ZERO '— CHECK SPAN I— ONE CYCLE SET ALARM ASSIGN -1— RELAYS ALARMS    I— ANALOGUE CLOCK NEW PASS —|— ASSOCIATE WINDOWS —i— SUPERVISOR OPERATOR SELECT SCREEN UDEF DEFINE SCREEN VARS NONE RS232 MODBUS ASCII MODBUS RTU ETHERNET SERIAL ALARMS FAULTS 1— DISPLAY ALARMS I— ALARM HISTORY 1— DISPLAY FAULTS '— FAULT HISTORY

 Open the catalog to page 4

Servomex 2500 QuickStart Manual 2500 Series - Configuration and Operation III

 Open the catalog to page 5

Servomex 2500 QuickStart Manual 2500 Series - Configuration and Operation

 Open the catalog to page 6

Servomex 2500 QuickStart Manual 1.1 Warnings, Cautions and Notes This publication includes WARNINGS, CAUTIONS and NOTES which provide information relating to the following: WARNINGS Hazards which could result in personal injury or death. CAUTIONS Hazards which could result in equipment or property damage. NOTES Alert the user to pertinent facts and conditions. 1.2 About this manual This manual covers software configuration and operation for the 2500, 2520 and 2550 range of analysers. Further copies of this manual may be ordered (part number 02500/003D). • Addresses for technical assistance...

 Open the catalog to page 7

Servomex 2500 QuickStart Manual KEY TO FIGURES Figure A Analyser Front View 1.    16 Character 2 line VF Display 2.    Hard key to    select Measurement Display 3.    Hard key to    select Menu Display 4.    Hard key to    Exit to the previous menu level 7. Hard key to Enter data or accept highlighted option within Menu 8.    Up/Down/Left/Right Cursor keys to select Menu options and increase/ decrease numerical values Figure B Analyser Menu Map Figure C Auto calibration Examples Schematic 1.    Autozero 2 2500 Series - Configuration and Operation 02500/003D/0

 Open the catalog to page 8

Servomex 2500 QuickStart Manual INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warnings, Cautions and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction to the user interface. . . . . . . . . . . . . . . . . . . . . . . . . INITIAL CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power up procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General access to analyser functions Setting passwords ....

 Open the catalog to page 9

Servomex 2500 QuickStart Manual 1.3 Introduction to the user interface See Figure A. The keypad and display used on the 2500 series analysers have been designed to be easy to operate and have a minimum number of keys. There are only 4 single-function (‘hard’) keys: MEASURE; MENU; ENTER; EXIT. There are also 4 cursor (directional) keys: Up; Down; Left; Right; these are arrow-head shapes. All keys require only a modest pressure to operate them, and give tactile feedback. Information is displayed on a 2-line, 16-character vacuum fluorescent display which ensures good visibility under all...

 Open the catalog to page 10

Servomex 2500 QuickStart Manual INITIAL CONFIGURATION 2.1 Power up procedure WARNING Ensure that the instrument variant is properly installed before proceeding. Confirm that all electrical and plumbing connections have been correctly made as described in the installation manual. Follow the Power up procedure as detailed in the installation manual. The normal measurement display will then appear and the 2500 will be operational. NOTE • The measurement will not be valid at this point since process sample is not yet flowing. • If a heated cell is fitted, it will not yet be up to temperature...

 Open the catalog to page 11

Servomex 2500 QuickStart Manual 2.2 General access to analyser functions It is recommended that the user refers to the menu map (see Figure B) and locates the function required. Then, using the keypad and display, follow the route as mapped. It will often be necessary to enter the password. NOTE The factory-default password for the 2500 series is ‘2000’ – this must be entered. Alternatively, if a keyswitch has been fitted this should now be closed. Failure to close the keyswitch is interpreted as an invalid password, and this should prompt the user to operate the keyswitch at this point....

 Open the catalog to page 12

Servomex 2500 QuickStart Manual Illegal times/dates outside the range of the clock are not accepted. 2500 Series - Configuration and Operation 0

 Open the catalog to page 13

Servomex 2500 QuickStart Manual 2500 Series - Configuration and Operation 02500/003D/0

 Open the catalog to page 14

Servomex 2500 QuickStart Manual 3. MAIN CONFIGURATION 3.1 Alarms There are 4 concentration alarms for each measured component on the 2500 series, and these are called ‘AL1’, ‘AL2’, ‘AL3’ and ‘AL4’. These must now be set up to suit the measurement and control needs of the particular installation. Factory default settings are 70%, 80%, 90% and 100% fsd respectively, and HIGH activation. Each enabled alarm has four parameters which need to be set up: i) FREEZE to prevent alarms during calibration, or FOLLOW so that alarms may be activated by calibration gases. ii) HIGH concentration alarm or...

 Open the catalog to page 15

Servomex 2500 QuickStart Manual provided. The hardware locations and terminal strip identifiers are given in the installation manual. Each relay output may be assigned to any combination of the following functions: i) Any of the concentration alarms for any of the measured components, in any combination. iii) Fault. Any existing relay allocation may be edited or cleared. When cleared, the relays will remain non-functional. NOTE • The Calibration in Progress function is active whenever a Manual Calibration or Check, or an Auto calibration or Autocheck routine, is in progress. • The Fault...

 Open the catalog to page 16

All SERVOMEX catalogs and technical brochures

  1. 4900 Multigas

    4 Pages