SERVOPRO 4000 Series Manual - 74 Pages

Add to MyDirectIndustry favorites
SERVOPRO 4000 Series Manual

Catalog excerpts

SERVOPRO 4000 Series Analysers Part Number: Revision: Language: SERVOMEX \ A MEASUREABLE ADVANTAGE

 Open the catalog to page 1

Instrument Configuration

 Open the catalog to page 3

WARNING Warnings highlight specific hazards which, if not taken into account, may result in personal injury or death. CAUTION Cautions highlight hazards which, if not taken into account, can result in damage to the analyser or to other equipment or property. NOTES Alerts the user to pertinent facts and conditions. Refer to installation manual ii

 Open the catalog to page 4

SECTION 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 1.2 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 1.3 Location of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 1.4 Transducer site numbering system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 1.5 Output numbering...

 Open the catalog to page 5

SECTION 7 TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 7.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 7.2 Generic 4000 series analyser performance . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 7.2.1 Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 7.2.2 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 7.2.3 Design standards . . . . . . . . . . . . . . . . . . . . . . . ....

 Open the catalog to page 6

List of Tables Table 1.1: Table 1.2: Table 3.1: Table 3.2: Table 3.3: Table 3.4: Table 3.5: Table 3.6: Table 3.7: Table 4.1: Table 4.2: Table 4.3: Table 4.4: Table 7.1: Table 7.2: Table 7.3: Table 7.4: Table 7.5: Table 7.6: Table 7.7: Table 7.8: Table 7.9: Table 7.10: Table 7.11: Table 7.12: Table 7.13: Table 7.14: Table 7.15: Table 7.16: Table 7.17: Table 7.18A: Table 7.19A: Table 7.18B: Table 7.19B: Transducer FSD values and availability in product range . . . . . . . . . . 1.6 Recommended calibration periods . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7 Signal terminal...

 Open the catalog to page 7

Warning You must install and use the instrument in accordance with the requirements of this manual. If you do not, people may be injured, the protective facilities incorporated into the design of the instrument may not operate as intended, sample gas measurements may not be accurate, or the instrument may be damaged. The instrument must be installed by a suitably skilled and competent technician or engineer. You must not modify the instrument in any way (either mechanically or electrically). If you do, the certification of the instrument will be invalidated and it may not operate safely....

 Open the catalog to page 8

This manual contains information regarding installation and hardware configuration of the Servomex 4000 series analysers. A separate Quickstart manual is also supplied with the analyser, reference part number 04000/003D. This details software configuration and operation of the analyser. Extra copies may be ordered from Servomex. Details of the hardware and instructions for servicing, by qualified personnel only, are presented in the 4000 Series Service Manual. This may be ordered from Servomex using part number 4000002D. Technical assistance and spare parts are available from Servomex...

 Open the catalog to page 9

A number of optional features are available for the 4000 series. These may include the following, depending upon analyser configuration: • Flow meters and needle valves (on the 4900D only) to monitor and control sample gas flow through the instrument. • A sample filter to protect the gas sensor modules from particulate contamination. • A sample flow alarm to monitor the sample flow and alarm when the flow falls below a defined level. This is only available on 4100D (Gfx flow driven) and 4900C product. • An autocalibration manifold (for a single sample stream) to allow the instrument to be...

 Open the catalog to page 10

Figure 1.1 identifies the location of the key features of the analyser. Note that the identification label (including serial number information) is located on the underside of the unit towards the rear. Figure 1.1: Key features of 4000 series analyser 8    Sample inlet(s) 9    Mains power connector 13 Serial output/Modbus port 14    Signal terminals Key A FRONT VIEW B    REAR VIEW 1    Sample filter (optional) 6    Needle valve(s) (optional) 7    Rack mounting brackets

 Open the catalog to page 11

1.4 Transducer site numbering system The four internal transducers are assigned site locations represented as I1, I2, I3 and I4 on the display. In the case of the 4100 and the 4200 analysers, each transducer is served by a discrete sample inlet and outlet connection on the rear panel. In the case of the 4900 analyser, either one or two sample streams may be specified -consequently only inlets/outlets numbered 1 and 2 will be used. 1.5 Output numbering system Identification numbers appear on the rear label to identify the terminals where each output appears and on the display when the...

 Open the catalog to page 12

NOTE The following abbreviations are used throughout this manual: Gfx IR Pulsed infra-red transducer Paramagnetic transducer Gas filter correlation infra-red transducer Zirconia transducer Conversion of transducer measuring units As supplied, the standard transducers within the analyser will measure in the units indicated in Table 1.1. It is possible to change these units by the use of a linear scale factor (refer to Quickstart manual). The user should note that the 4000 series software prime measurement is in percentage, therefore trace level 'vpm' (volume parts per million) measurements...

 Open the catalog to page 13

All SERVOMEX catalogs and technical brochures

  1. 4900 Multigas

    4 Pages