Seraphin - 30 Indel Avenue Ζ Rancocas, NJ 08073 Tel: 1-609-267-0922 Fax: 1-609-261-2546 e-mail: [email protected] Pub E91-4044 >

PEMBERTON FABRICATORS, INC. (SERAPHIN > DIVISION) SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS IN THIS MANUAL OR OMISSIONS FROM THIS MANUAL. SERAPHIN > ή MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THIS MANUAL AND, IN NO EVENT, SHALL SERAPHIN > BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PRODUCTION, LOSS OF PROFITS, ETC. PRODUCT NAMES USED HEREIN ARE FOR MANUFACTURER OR SUPPLIER IDENTIFICATION ONLY AND MAYBE TRADEMARKS/REGISTERED TRADEMARKS...

3 Description: The Seraphin Slip-on with prover is a mobile proving system designed to calibrate gasoline and diesel fuel dispensers. It is comprised of (3) precision volumetric stainless steel bottom drain special J provers connected each to their own individual 80 gallon SS holding tank witha 50 Gallon Series J prover is installed above the holding tanks for testing high speed diesel dispensers. The 80 gallon configuration allows for up to 48 (5-gallon) or 6 (50 Gallon) calibration tests before returning to the fuel station's storage tank for dumping. The prover drain valve is plumed to piping...

4 5.Visually inspect, from the top neck opening, the interior of the prover to ensure it is free of debris which could affect the accuracy of the liquid volume measurement. Prover Wetting Procedure :1.If the prover is clean and free of debris, fill the prover with liquid from the meter device being checked. Fill the prover until the amount on the meter reads the nominal capacity of the prover. NOTE: The prover must be filled once and drained in order to wet the internal sides of the prover body. Wetting the internals of the prover helps ensure consistency in the amount of liquid that clings to...

CAUTION: Ensure all fuel residual is drained from the hose into the underground storage tank prior to lifting the hose from the storage tank inlet > CAUTION: Disposal of drained fluid should be done in an environmentally safe and responsible manner in accordance with good industry practices and in compliance with OSHA regulations SeraphinԮ - 30 Indel Avenue Rancocas, NJ 08073 Tel: 1-609-267-0922 Fax: 1-609-261-2546 e-mail: [email protected] Pub E91-4044 >

6 8. Stow the drained hose, secure the provers with the (3) locking brackets making sure to replace the cotter pins and replace vapor caps. Conducting a Proving Run with the 50 Gallon Series J Prover: 1. Close the Series J prover drain valve. 2. Perform the wet down procedure on the prover. Prover Wetting Procedure :1.If the prover is clean and free of debris, fill the prover with liquid from the meter device being checked. Fill the prover until the amount on the meter reads the nominal capacity of the prover. NOTE : The prover must be filled once and drained in order to wet the internal sides...

CAUTION: Disposal of drained fluid should be done in an environmentally safe and responsible manner in accordance with good industry practices and in compliance with OSHA regulations > CAUTION: Disposal of drained fluid should be done in an environmentally safe and responsible manner in accordance with good industry practices and in compliance with OSHA regulations Seraphin - 30 Indel Avenue Ζ Rancocas, NJ 08073 Tel: 1-609-267-0922 Fax: 1-609-261-2546 e-mail: [email protected] Pub E91-4044 >

Reference: For officially recognized petroleum measurement procedures and methodsreference: NIST Handbook 44 Specifications, and Tolerances, and other Technical Requirements for Weighing and Measuring. API Manual of Petroleum Measurement Standards, Chapter 4, Section 4 (Tank Provers) and Section 8 (Operation of Proving Systems). Care and Maintenance of Provers 1. Check provers, valves and piping periodically for dents and leaks at the seams, joints, connections and gauge assembly. If a leak is detected, call SERAPHIN > ׮ for authorized repair parts. > Seraphin - 30 Indel Avenue Ζ Rancocas, NJ...

Bottom loading: Method of filling a volumetric vessel. Intake is made with a bottom load adapter. Capacity, nominal : T he nominal capacity of a field standard test measure or prover is the volume used to designate the measure or prover. The volume is determined by the nominal mark on a graduated upper neck gauge and between the nominal mark on the graduated upper neck gauge and the lower shut off valve or zero mark on a lower neck gauge on a prover. > NOTE: The nominal capacity of the prover has be set at the Seraphin facility using Standards that are traceable to the National Institute of Standards...

Seraphin - 30 Indel Avenue Ζ Rancocas, NJ 08073 Tel: 1-609-267-0922 Fax: 1-609-261-2546 e-mail: [email protected] Pub E91-4044 >

PO BOX 227 30 INDEL AVENUE RANCOCAS, NJ 08073-0227 > PEMBERTON FABRICATORS, INC. FULLY WARRANTS THAT THE PRODUCT SUPPLIED SHALL CONFORM TO THE DESCRIPTION IN THE QUOTATION AND AGREES TO REPAIR OR REPLACE F.O.B. SHIPPING POINTS, ANY PARTS EXCEPTING EXPENDABLE ITEMS SUCH AS FILTERS AND LIGHTS THAT FAIL DUE TO DEFECTS IN MATERIAL OR WORKMANSHIP WITHIN ONE YEAR OF USE OR 18 MONTHS AFTER SHIPMENT, WHICHEVER OCCURS FIRST. Other than those expressively stated herein, there are no other warranties of any kind, expressed or implied, and specifically excluded but not by way of limitation, are the implied...