Catalog excerpts
water-cooled Temperature Control Unit SENQW Series Provides controlled temperature coolant for secondary coolers Cooling water at a precisely-controlled temperature with ± 1° F (0.5° C) accuracy. A temperature control unit (TCU) provides controlled temperature water (coolant) to a group of secondary sample coolers in order to ensure closely controlled sample temperatures. Self-contained with all necessary controls, pumping and refrigeration systems. Wide condenser cooling water temperature range: 55-105°F (13-41°C). Options available as low as 30°F or as high as 115°F (46°C). Optional heater for additional warming capacity for subcooled samples. Local display provides quick operational snapshot. Model: SENQW Sentry temperature control unit (TCU) systems are pre-designed, pre-piped packages available in sizes from 3 to 15 tons, air or water-cooled. All components are easily accessible for service. Each Sentry TCU system undergoes a factory “run-in” under a range of heat loads. Measurements are taken of critical parameters and recorded for future reference. Condenser Water Flowrate gpm (lpm) Condenser Water Press Drop psi (bar) Cooling Capacity¹ Chilled Water Flowrate ¹Cooling capacity based upon 105°F (41°C) condenser water and 76°F (24°C) coolant setpoint, 60 Hz power. ²MCA = Minimum Circuit Ampacity; used for main power wire sizing (not including Aux. Heater). ³Cooling and heating capacity is reduced about 17% for 50 Hz power.
Open the catalog to page 1WATER-COOLED TCU TECHNICAL DATA Dimensions Condenser Water Chilled Water Right View Rear View SPECIFICATIONS Refrigeration • Keypad control to run system or pump alone • Microprocessor based PID temperature control • Digital contact provided for remote system start • Digital indication of chilled water outlet temperature • Clear display of operational warnings and alarms • General fault alarm contact for remote indicator • Hermetically-sealed scroll compressor • Full factory refrigerant charge of HFC‑410A • Copper brazed 316L stainless steel evaporator • Hot gas bypass valve for precise...
Open the catalog to page 2All Sentry Equipment catalogs and technical brochures
-
SENTRY ISOLOK SAA SAMPLER
2 Pages
-
SENTRY SA SAMPLER
2 Pages
-
SENTRY B1 SAMPLER
2 Pages
-
SENTRY SINGLE LINE
2 Pages
-
SENTRY VREL CONTROL VALVE
2 Pages
-
SENTRY SBC CONTROLLER
2 Pages
-
SENTRY ISOLOK MSA SAMPLE
2 Pages
-
Sample Coolers
8 Pages
-
Sample Sequencer 5
2 Pages
-
DCCP Reboiler
2 Pages
-
Corrosion Product Sampler
2 Pages
-
Resin Column (RC 100)
2 Pages
-
Resin Column (RC 200/400)
2 Pages
-
Thermal Shut Off Valve (TSV)
2 Pages
-
AutoVREL
2 Pages
-
VREL
2 Pages
-
TCU Air Cooled
2 Pages
-
Manifold Valve
2 Pages
-
Sentry Sample Coolers
8 Pages
-
Sentry Automatic Samplers
8 Pages
-
API Sampling Suite
4 Pages
-
Sample Chiller
2 Pages
-
Sample Cooler TLR
2 Pages
-
Blowdown XC
2 Pages
-
Dual Tube Coil Sanitary
2 Pages
-
Dual Tube Coil (DTC-8)
2 Pages
-
Dual Tube Coil (DTC-4)
2 Pages
-
Dual Tube Coil (DTC-6)
2 Pages
-
Spiral Heat Exchanger
2 Pages
-
SampleCooler USC
2 Pages
-
Sample Cooler WSW
2 Pages
-
Sample Cooler TRB
2 Pages
-
Sample Cooler FXR
2 Pages
-
Sample Cooler FLR
2 Pages
-
Model MSE ISOLOK®
2 Pages
-
Model MSD ISOLOK®
2 Pages
-
Sentry MT-1 Magnetic Trap
2 Pages
-
Sentry MT-2 Magnetic Trap
2 Pages
-
Sentry MT-5 Magnetic Trap
2 Pages
-
Sentry AutoVREL Spec Sheet
2 Pages
Archived catalogs
-
Manifold Valve
2 Pages
-
TCU Air-Cooled
2 Pages
-
VREL®
2 Pages
-
AutoVREL
2 Pages
-
Twist-Lock Cell Holder (TLC)
2 Pages
-
Thermal Shut-off Valve (TSV)
2 Pages
-
Resin Column RC200/RC400
2 Pages
-
Resin Column RC100
2 Pages
-
Corrosion Products Sampler
2 Pages
-
Sample Sequencer® 5
2 Pages
-
Sample Coolers
8 Pages
-
Power Generation Solutions
6 Pages
-
Spiral Tube / Tube-in-Tube
8 Pages
-
Model RPG Data Sheet 18.1.4
2 Pages
-
Model MCL Sampler IOM
1 Pages