*mydirectindustry

12HPC

Product catalog summary

Overview: The document provides technical specifications for the Model 12HPC, a low-cost, wirewound, bushing mount potentiometer that is RoHS compliant. It includes details on special specifications, general specifications, and standard model numbers.

Specifications:

Available in 3-turn, 5-turn, and 10-turn types.
Features include a shaft with front and rear extension, special machining on the shaft, and a simple sealed housing.
Standard resistance range is from 100Ω to 50kΩ for 5-turn and 10-turn models, with a maximum practical resistance value of 100kΩ for 10-turn models.
Total resistance tolerance is ±3% for standard class and ±1% for precision class.
Independent linearity tolerance varies by model: ±0.35% for 5-turn and ±0.25% for 10-turn in standard class; ±0.2% for 5-turn and ±0.1% for 10-turn in precision class.
Power rating is 0.75W for 5-turn and 1.5W for 10-turn models.
Noise level is within 100 E.N.R.
Electrical travel is 360° × n ±5° (n: number of turns), and mechanical travel is 360° × n + 15°.

Materials and Construction:

Resistance wire used is Cu-Ni system for 5-turn and Ni-Cr system for 10-turn models.
Available with lug terminals, rear lug terminals, and pin terminals for PCB mounting.

Mechanical Specifications:

Insulation resistance is over 1,000MΩ at 500V.D.C.
Dielectric strength is 1 minute at 1,000V.A.C.
Starting torque is within 3mN・m (30gf・cm).
Stopper strength is approximately 0.15N・m (1.5kgf・cm).
Appropriate fastening torque of the nut is within 0.8N・m (8kgf・cm).
Resistance temperature coefficient is ±20p.p.m./°C.
Mass is approximately 10g for both 5-turn and 10-turn models.

Additional Notes:

Special specifications may alter general and environmental specifications; consultation is advised.
Standard dimensions and terminal hole layouts are provided, with specific instructions for panel mounting hole processing.

Catalog excerpts

MODEL 12HPCLow-cost Item Wirewound # Bushingmount # RoHS Compliant U&iMV Standard Model Numbers Bushingmount type General Specifications Standard Dimensions With lug terminals (With metric dimensions) With pin terminals for p.c. board With rear lug terminals 13 + 0.5 Terminal Holes Layout Multi turn ► Contact type ► Wirewound Standard Resistance Rangeange Note: 1.1 pc. each inner teeth washer and hex nut are attached. 2. Outer dimension of 5-turn version is the same as those of 10-turn. 3. Please process the mounting hole on the panel. The diameter should be 7.14mm+ 0.05. o # Standard Resistance Values ■ No. of Wire Turns ■ Resistance Wire Used Resist. Value (Q) Note: Mark>5;shows special high resistance value. _ . (In case of the potentiometer with special specifications, the general specifications • Special Specifications Available and environmental specifications may change. Please consult us in advance.) 0 3-turn type (SI 2HPC-3) 0 Shaft with front and rear extension (Rear shaft with 0.8mm dia. and 10mm length) 0 Special machining on the shaft 0 Simple sealed housing "shanghai sibo m & e CO.,ltd.

Open the catalog to page 1

All SENTOP by Shanghai Sibo M&E Co., Ltd. catalogs and technical brochures

Archived catalogs

JOYSTICK 100JB
2 Pages
FCPS22AC
2 Pages
FCP22AC
2 Pages
JOYSTICK 30JL
2 Pages
JOYSTICK H30JH
2 Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list