*mydirectindustry

Catalogs
SENSOREX MEGGITT
Strain gauge conditioner SX3310

Strain gauge conditioner SX3310

Product catalog summary

Overview
Meggitt Sensing Systems specializes in various measurement product competencies including LVDTs, inertial systems, inclinometers, accelerometers, IMUs, MEMS sensors, servo-inclinometers, and conditioners. These products are applicable in sectors such as aerospace, energy, measurement, and railway.

Product Focus: SX3310 Strain Gauge Conditioner
The SX3310 is a DIN box strain gauge conditioner known for its low bridge impedance, down to 120 ohms. It features simple zero and scale adjustments using dip-switches and potentiometers. The unit is designed for easy maintenance and installation with screw terminal connections and can be mounted on a DIN EN 50022 track.

Key Specifications

Power Supply: 24VDC ±8VDC
Transducer Excitation: 5VDC or 10VDC
Output Signal: 0/10V or ±10V and 4-20mA
Wiring Transducer: 4 or 6 wires

Mechanical & Environmental Characteristics

Dimensions: 115x100x23 mm
Box Material: Polyamide PA
Protection: IP 20
Operating Temperature: 0°C to +70°C
Storage Temperature: -40°C to +85°C
Weight: Approximately 130 g

Electrical Specifications at +25°C

Power Supply: 24VDC ±8VDC, Maximum consumption 150mA
Strain Gauge Excitation: 5VDC or 10VDC
Input Amplifier Current: 5nA, Impedance 1010 ohms typical
Gain: Maximum 8500, Minimum 80
Voltage Output: Gain=1000/ ±0.001% of Full Scale
Current Output: Maximum non-linearity ±0.015% of Full Scale

Contact Information
Meggitt (Sensorex), Archamps Technopôle, 196 Rue Louis Rustin, 74166 ARCHAMPS, France. Tel: 04 50 95 43 70, Fax: 04 50 95 43 75, www.sensorex.fr, www.meggitt.com

Catalog excerpts

Aerospace Energy Measurement Railway Characteristics • Power supply 24VDC ±8VDC • Transducer excitation 5VDC or 10VDC • Output signal 0/10V or ±10V and 4-20mA • Wiring transducer 4 or 6 wires SX3310 module is a strain gauge conditioner with very low bridge impedance (down to 120 ohms). This module has a very simple and practical zero and scale adjusting with dip-switches and potentiometer. Connections for power supply, transducer and output signals are made by screw terminals to facilitate maintenance and installation. This industrial unit in polyamide PA PHOENIX EM type may be plugged into any common DIN EN track (EN 50022 standard). Our measurement product competencies: LVDTs I Inertial systems I Inclinometers I Accelerometers I IMU I MEMS sensors I Servo-inclinometer I Conditioners MEGGiTT smart engineering for extreme environments

Open the catalog to page 1

V Sensorex® DIN box strain gauge conditioner SX3310 Aerospace Energy Measurement Railway polyamide PA Screw terminal Operating temperature Storage temperature Temperature stabilization time Power supply Power supply Maximum consumption Strain gauge excitation Strain gauge Mini. impedance for 5VDC excitation Mini. impedance for 10VDC excitation Sensitivity Input amplifier Current Impedance Gain Maximum Minimum Zero Maximum for a 120 ohms impedance ±3.25mV/V Voltage output Maximum non linearity Short circuit current Outputs Current output Maximum non linearity Impedance Load resistor (for...

Open the catalog to page 2

Aerospace Energy Measurement Railway Sensorex® DIN box strain gauge conditioner SX3310 Selection guide Contact MEGGiTT smart engineering for extreme environments Meggitt Sensing Systems Our measurement product competencies: LVDTs I Inertial systems I Inclinometers I Accelerometers I IMU I MEMS sensors I Servo-inclinometer I Conditioners

Open the catalog to page 3

Strain gauge conditioner SX3310

Strain gauge conditioner SX3310

Catalog excerpts

All SENSOREX MEGGITT catalogs and technical brochures