Multitrans
4Pages

MULTITRANS or EP ABRASION RESISTANCE For average to severe working conditions Areas of application Our MULTITRANS range is used for conveying all types of materials, in bulk, cold (<80°C) and neutral, in all extraction and transformation industries, under average to severe working conditions. • Quarries/sand pits (grain size < 400 mm) • Thermal power plants (coal, ash) • Cement works (quarry materials, added materials, cold clinker) • Fertiliser factories / Chemical plants (non chemically aggressive materials) • Port installations (ores, coal, phosphates) • Mining/Iron and Steel Industry (ores, coke, added materials) • Paper mills (wood, edgings) • Salt marshes / Salt works • Sugar factories (sugar beet and sugar beet chips) • Glassworks (raw materials, cullet) Our MULTITRANS belt consists of 3 to 5 EP (polyester warp and polyamide weft) synthetic fabric plies with a rubber interface, the thickness of which varies according to the type. • The low-elongation polyester fibres are used in the warp direction to reduce the length of the tension travels • The more elastic polyamide fibres are used in the weft, to ensure good troughing. • The carcass is protected by covers of D grade (superior quality anti-abrasive) which is recommended for very abrasive products and sharp materials (Abrasion loss as per NFT 46012, ISO 4649 and DIN 53516, average value 100 mm3). These belts can also be produced with X, Y or Z cover grades standardised as per DIN 22102. IMPORTANT NOTICE: This brochure has been prepared carefully, to advise our customers. The information stated therein is state of the art and the results of different tests carried out over several years. Individual operating conditions affect any product, which means that a product can only offer the safety that can be expected on the basis of the data provided in our product information. In the event that the product is used otherwise than in conformity with the specifications, such safety may not be assumed. Our responsibility is limited exclusively to delivery of the conveyor belt in accordance with the specifications. Please note: Before using the product in new areas of application which are not covered by the product information a Sempertrans engineer MUST be asked for advice. Stocking, care and maintenance of all our products must be performed according to our stocking, care and maintenance guidelines and according to ISO 5285 standard ; Subject to errors and printing errors. Reproduction of any kind - also of excerpts - only upon express written consent of Sempertrans. The brochure shall remain the property of Sempertrans and is the most recent version. All transactions shall be exclusively subject to our general terms and conditions. Date of publication 06/2007 1st edition Subject to changes. The figures stated in our documents are mean approximate values for information but no specified or warranted values.

• The usual designation of MULTITRANS or EP is as shown in the example below: 1600 Rated width of belt (mm) Carcass Rated breaking strength in warp direction (N/mm) Number of plies of fabric Thickness of top cover and bottom cover (mm) Cover grade: superior anti-abrasive • The type of belt (rated breaking strength in N/mm) is obtained by superimposing plies of fabric: TYPE N/mm IMPORTANT NOTICE: This brochure has been prepared carefully, to advise our customers. The information stated therein is state of the art and the results of different tests carried out over several years. Individual...

SEMPERTRANS® standard RANGE, Cover of grade D (superior quality anti-abrasive), X, Y or Z (as per DIN 22102) The range indicated in this table is our standard range. On order, manufacturing is possible: - in specific cover thicknesses of 3+1.5 to 15+10 - in belts with moulded edges or cut edges - in all the cover grades specified on pages 66 and 67. Note: certain cover grades are not compatible with all the above constructions. For further information, consult our technical Remark: manufacturing minimum for belts not in stock: 2 x 200 m for belts of width less than or equal to 800 mm, 1 x...

The approximate thicknesses and weights of the belts can be determined from the enclosed tables giving: • the thickness and the weight of the carcass • the density of the various standard anti-abrasive covers For other cover grades, consult our technical departments for the weight and thickness. Carcass designation These values are given for information. TECHNICAL SPECIFICATIONS Cover grade / resistance of covers to products conveyed Pulley diameter Tension travel Trough transition lengths Radius of curvature Turnover Idler spacing Roller skirt clearance Splicing Approximate values given...