SenseCAP All-in-One Weather Station V2 Catalog
50Pages

User manual/ Technical information SenseCAP All-in-One Weather Station User Guide（V2） Version: V1.2 Dates: 2023-6-8 The 1 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information The 2 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information 1 Product Introduction SenseCAP ONE is a series of all-in-one compact weather sensors, including S1000 10-in-1, S800 8-in-1, S700 7-in-1, S500 5-in-1, S200 weather sensors. These weather sensors integrate multiple sensors into this compact device, monitoring up to10 weather parameters: air temperature, air humidity, atmospheric pressure, light intensity, wind speed, wind direction, precipitation, PM 2.5, PM 10,noise and CO2. The sensors use ultrasonic to measure wind speed and wind direction, to achieve high-precision data collection, which is easy...

User manual/ Technical information 0~60 m/s standard range Wind speed 0~75m/s extended range Up to 80m/s withstand range Product Model: S700 (7-in-1) Measurement Parameter Measurement Range Measurement Accuracy Barometric pressure 0~60 m/s standard range Wind speed 0~75m/s extended range Up to 80m/s withstand range Light intensity Rain intensity Product Model: S800 8-in-1) Measurement Parameter Measurement Range Measurement Accuracy Barometric pressure 0~60 m/s standard range Wind speed 0~75m/s extended range Up to 80m/s withstand range Noise intensity Product Model: S1000 (10-in-1,CO2...

User manual/ Technical information Measurement Parameter Measurement Range Measurement Accuracy Barometric pressure Wind speed Light intensity Rain intensity 400-5000ppm;exten 土(30 ppm +3% of reading) ded range up to (extended range ±10% of 1ppm 10000 ppm reading） Note: Multi-in-one meteorological environment sensors with other monitoring elements CO2 can be customized. For specific requirements, please contact relevant personnel of the company. The 5 Page total 50 Page Seeed www.seeedst

User manual/ Technical information 2 Installation Before the installation, check the packing list and make sure there are no missing parts. The 6 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information 2.1 Packing List Number SenseCAP ONE All-in-one compact weather sensor M12 8-pin communication cable (default length 3-meter hook-up wire, and there is a waterproof aviation connector type to choose when working with SenseCAP SensorHub datalogger. If the aviation connector is not needed, cut it off by yourself) USB Type-C cable, for configuring devices Flange plate (purchased separately) Pole adapter sleeve base (purchased separately) Pole adapter cross bar (purchased separately) The 7 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information 2.2 Installation 2.2.1 Device Interface Introduction USB port for configurationOpen with a coin Data and power connector There are two connectors at the bottom of the device. • USB Type-C interface allows you to connect your computer with a normal USB Type-C cable to the device for configuration. The main data interface can be connected to the M12 8-pin cable, supporting multiple bus protocols The 8 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information 2.2.2 Connect with USB Cable Note: The white cover (on the side near the label) should be tightened after debugging to prevent water from entering the device! The 9 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information The device adopts an M12 8-pin connector, the different colored pins provide power and data communication (as shown in the above diagram). When working with the RS-485, you can connect only 4 wires (not using a heating function), and the rest can be individually wrapped with tape to prevent short circuit The holes of the cable and the pins of the device connector must be aligned when the cable is plugged in. The 10 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information Plugin the cable and tighten it clockwise Note: the cable is aimed at with the bottom before inserting it into the bottom. Otherwise,the pins are skewed may cause the communication is abnormal . When using the device with a heating function, a separate 24V (24V@1A is recommended) power supply is required. Gray wire #5 is connected to the negative of the power supply, and pink wire #6 is connected to the positive pole of the power supply. The 11 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information Reminding: 1. When the device needs to add power extension cable, if its length is more than 100 meters, it needs to use 24V/2A for power supply (without heating function); 2. When the heating function is enabled, the power supply of the heating module should be within 3 meters of the SenseCAP ONE.The distance between the power supply of the heating module and the device is not more than 5m. Please use the 3m / 5m conversion cables sold by our company. 2.2.4 Install the device. There are two major installation methods, either mount on a pole with a sleeve...

User manual/ Technical information The size of the sleeve is shown below. The 13 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information It is recommended that the diameter of the pole should be less than or equal to 75cm. The 14 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information Note: Please tighten the screws ! The dimension of the flange plate is shown below. The 15 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information The 16 Page total 50 Page Seeed www.seeedstudio.com

User manual/ Technical information 3 Device's Operating Mode After installation, you can power on the device, configure it and collect data from the device. The device has two operating modes, configuration mode, and working mode. Configuration Mode With a USB cable, you can check or configure the device’s parameters, such as device name, version number, and communication protocol configuration. Product firmware can be upgraded in this mode. Working Mode Connect the devices and data logger with an M12 data and power cable, and then the data collected by the device will be sent to the host...