SYS-B68-IPC INSTALLATION, USE AND WARNINGS MANUAL

Information subject to change. Please visit www.seco.com to find the latest version of this manual. Page.1 of 16

Preliminary information Device description The SYS-B68-IPC device is a single board computer enclosed in a metal box with a heat sink. The SYS-B68-IPC device integrates a single standard NUC board based on the eighth generation Intel® Atom, Pentium® and Celeron® family of System-on-Chips (SOC) previously coded as Apollo Lake, a series of SOC Dual / Quad with a set of 64 bit instructions. The technology developed by SECO S.p.A. for the SYS-B68-IPC device can be used and applied in various fields, such as: Digital Signage Infotainment Edge Computing Information subject to change. Please visit www.seco.com...

This manual is intended for ordinary people and installers (expert users). The warranty shall be voided in the event of: • failure to comply with safety regulations; tampering with the device; changes to the safety conditions established by the Manufacturer in the device management software; use of the device by untrained and/or unauthorised personnel or failure to respect duties, as indicated in the manual; changes or repairs carried out by the user without written authorisation from the Manufacturer; partial or total failure to comply with the instructions; defects in the mains power supply...

Manufacturer identification SECO S.P.A. Via Achille Grandi n°20 52100 Arezzo – Italy Tel: +39 0575 26979 Fax: +39 0575 350210 Device identification Serial number Device identification plate The device is equipped with an identification plate located on the side. The plate features the device identification information to be reported to Seco S.p.A. if necessary, as shown in the table: IPC - Code that identifies the Client. XXXX–1XXX - Code that identifies the electronic board inside the device (reference page 14). I3 – Code that identifies the temperature range and revision index of the device....

Caution! It is strictly forbidden to remove the identification plate and/or replace it with other plates. Technical specifications SYS-B68-IPC device hardware specifications The table below features the board hardware specifications: Screen Section Mass Storage Network connection USB Audio Serial ports Other interfaces Electrical Power Supply Intel® Atom™ x7-E3950 Quad Core @1.6 GHz (Burst 2.0GHz), 2MB L2 Cache, 12W TDP Intel® Atom™ x5-E3940 Quad Core @1.6 GHz (Burst 1.8GHz), 2MB L2 Cache, 9.5W TDP Intel® Atom™ x5-E3930 Dual Core @1.3 GHz (Burst 1.8GHz), 2MB L2 Cache, 6.5W TDP Quad Channel soldered...

Operating System Optional Accessories Operating temperature in user environment Humidity Type of installation Preinstalled OS (factory options): Microsoft Windows 10 IoT entry Linux Ubuntu 64-bit Available on request: Wind River Linux (64-bit) Yocto (64-bit) Android (planning) miniDP++ to HDMI adapter Customised bracket for VESA panel mount -40°C ÷ +85°C** 5% ÷ 85% Fastening with screws Attention! **The values indicated refer to the maximum temperature of the environment of use of the device. It is the customer’s responsibility to verify that the temperature remains within the admissible range...

Software Specifications BIOS B6I FLASH software version released on the website https://www.seco.com/it/sys-b68ipc.html , which is always updated and available, even in later versions. Reference directives SECO S.p.A. places the device on the market, equipping and providing it with: - CE marking Declaration of Conformity FCC - Part 15 Certification* ISED Certification** * (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with...

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Ce dispositif a été conçu pour fonctionner avec les antennes fournies avec ce produit. L’utilisation d’autres antennes peut enfreindre les règles industrielles du Canada et annuler l’autorité de l’utilisateur quant...

Safety devices Warnings Caution! It is the user’s responsibility to apply preventive and protective measures, in accordance with the legislation of the country of installation and use of the device. Caution! Only use CLASS 2 power supply with double isolation output and LPS operation (see EN 60950-1 clause 2.5) or ES1 PS2 output (see EN 62368-1) as per reference Standards: • Caution! Only connect certified peripherals / devices to the device. Important! Operations on the device must be carried out by specialized and authorised personnel only. Caution! Always disconnect the electrical power supply...

Safety pictograms affixed to the device The device is provided with adhesive labels and safety plates, as indicated in the table below. PICTOGRAM DESCRIPTION Danger of hot surfaces! Skin burns in case of contact Do not touch with your hands or other body parts DESCRIPTION Fire hazard Risk of device fire Do not use a power supply capable of supplying current values greater than 5 Amps Information subject to change. Please visit www.seco.com to find the latest version of this manual. Page.10 of 16

Characteristics and components of the device The SYS-B68-IPC device is a single board computer enclosed in a metal box with a heat sink. Caution! When running, the device can reach very high temperatures, causing the danger of burns when in contact with the heat sink. A back cover with 4 universal fastening points is fastened to the connection frame. The inserts are the only fastening system to integrate the device on any of the customer’s machines. Measurement layout Information subject to change. Please visit www.seco.com to find the latest version of this manual. Page.11 of 16