Control Units and Systems
6Pages

SCHEUGENPFLUG AG METERING AND DISPENSING TECHNOLOGY Control Units and Systems Control units and user-friendly operation – effective Control and Visualisation is key to future-proof production In today’s systems, control concepts and software greatly influence efficiency, since they affect the system’s usability, performance, and networking capability and as a result also its future viability. To fulfil both current and future requirements, Scheugenpflug has, in addition to processing technology, established comprehensive expertise in software development and control engineering. Various control systems are employed to meet the often highly specific hardware and software requirements in connection with dispensing technology as effectively as possible. For simple tasks, the second generation of a microcontroller-based PLC (SCP200) is used, and for more complex automation tasks the third generation of a combination of PLC and PC (Beckhoff PC and SoftPLC Twin-CAT). These systems allow user guidance and system programming to be ideally matched to the specific requirements of the respective dispensing task. (The page references refer to the general catalogue.) With Industrie 4.0 concepts and the growing demands on quality and associated traceability requirements, networking of systems is becoming ever more important. Scheugenpflug systems leave nothing to be desired here – be it linking of machines with each other, data gathering and evaluation, process and pot life optimisation, or communications with other systems and/or master control systems. As well as fulfilling all of these current requirements, the latest control concepts are prepared for future needs. Scheugenpflug’s comprehensive own software and control expertise is, furthermore, the foundation of its ability to offer state-of-theart solutions – and therefore economic efficiency – also in highly dynamic markets.

The Efficient Solution for material preparation and feeding units and for manual work stations All material preparation and feeding systems as well as the manual work stations are equipped with the specially designed microcomputer controller and visualisation SCP200. It monitors and controls all steps of the production process, from the docking of the follower plate and material preparation (heating, stirring, circulating, evacuating, filling level monitoring, automatic refilling in of material), over the feeding of the dispensing material into the system, to the actual metering and...

For small dispensing systems a PLC might be a too big solution. The proven SCP200, as a result, has been expanded to the SCP200+ with additional vacuum and motion functions, which turn also the versions of DesktopCell and LeanVDS that are equipped with this controller into fully-featured small dispensing systems. The result is simple and cost-effective. Parametrisation of pre-defined processes • Start position • Teaching • Pot-life monitoring and clearing of the mixing tube or metering needle • Matrix programming Control Units and Systems The characteristics in detail: • Intuitive...

Leading-Edge ease of operation custom designed for metering and dispensing – The effectiveness of a controller is determined at least as much by its user interface as it is by the hardware. The UVIS automation software specially developed by Scheugenpflug for cells, processing modules and vacuum dispensing systems represents a high-performance cutting-edge user interface which is tailor made for the purpose. It therefore provides an ideal solution for production and dispensing systems. The control system is convenient and easy to operate, which simplifies all monitoring, maintenance and...

UPIC Programming Tool Fast and Easy creation of the Dispensing Program best matching your task To create the ideal dispensing program, a software or CNC specialist or lengthy training were previously often needed. This is no longer the case with the programming tool UPIC-3D/DXF, coming with UVISneo and UVISnano, which allows any kind of dispensing program, dabbing, matrix or even CNC program to be created quickly and easily. The latest version now also features a 3D dispensing visualisation for checking and troubleshooting created programs. Optionally available is also a CAD-CAM interface...

International Sales and Service Scheugenpflug Resin Metering Exmore Benelux bvba CZECH REPUBLIC/SLOVAKIA KOREA RUSSIA AMTECH spol. s r. o. ETC CO.,LTD. Ostec Enterprise Ltd. 62100 Brno Kyunggi-Do, Korea (437-753) 121467 Moscow amtech@amtech.cz wblee@etcco.kr info@ostec-smt.ru www.amtech.cz www.etcco.kr www.ostec-smt.ru TechSpeed Bendkowski, Mazur Sp.j Errors and omissions excepted. Content is subject to technical changes.