Manual, Connectors to UIC 558
26Pages

{{requestButtons}}

Catalog excerpts

Manual, Connectors to UIC 558 - 1

9 ® SCHALTBAU Connect • Contact - Control Connectors UIC Series Inter-car jumpers to UIC 558 VE Manual F120.en

Open the catalog to page 1
Manual, Connectors to UIC 558 - 2

Connectors UIC 558 – Installation and Maintenance Instructions

Open the catalog to page 2
Manual, Connectors to UIC 558 - 3

Important Basic Information 1. Important Basic Information 1.1 Legal Notes Without prior written consent of Schaltbau GmbH, the instructions is not allowed to be electronically or mechanically reproduced – as a whole or in parts – be distributed, changed, transmitted, translated into another language or used in any other way. Schaltbau GmbH cannot be held liable for damage caused by not observing (or only partly observing) the Installation and installation instructions. 1.2 Conventions for this Installation and Maintenance Instructions This instructions describe the installation and...

Open the catalog to page 3
Manual, Connectors to UIC 558 - 4

General and Security Information ► A qualified electrician is a person who can judge and recognise the possible dangers of the jobs commended to him based on his training, knowledge and experience and by knowledge of the appropriate regulations. ► Staff must be informed clearly about who is responsible for the maintenance of the connectors. 2.3 Intended Use ► The connectors are intended for plug-in and detachable connections of components, devices and systems only. They are used for the transmission of power and signals. ► In order to comply with DIN EN IEC 61984 make sure that always the...

Open the catalog to page 4
Manual, Connectors to UIC 558 - 5

Dangers and Security Measures 3. Dangers and Security Measures 3.1 Electrical Dangers DANGER The connectors contain components that carry voltage. Risk of electric shock! Always observe the following safety regulations before beginning any work on electrical constructions: X Disconnect X Ensure that it is not possible to reconnect unintentionally X Clearly mark your work area X Make sure that there is no voltage present X Earth and short circuit the installation X Insulate or cover adjacent energized parts X Only an electrically skilled person may determine if there is no voltage present...

Open the catalog to page 5
Manual, Connectors to UIC 558 - 6

Dangers and Security Measures A CAUTION_ The connectors contain sharp-edged parts. Risk of injury! ► Use only appropriate tools afor maintenance work on the connectors. ► Wear protective gloves when working with sharp-edged components. 3.4 Measures for Avoiding Damages Aggressive fluids may damage the connectors. ► Make sure that the connectors are not exposed to aggressive fluids. Improper handling of the connectors, e.g. when hitting the floor with some impact, can result in breakage, bent pin contacts, cracks and deformation. ► Make sure that the connectors are always used properly. ►...

Open the catalog to page 6
Manual, Connectors to UIC 558 - 7

3.5 Measures for Avoiding Malfunctions In the case of damage, wear and tear and/or soiling of the connector components - in the form of a partial break, sharp edges and discoloured surfaces - the functional safety of the connectors is no longer guaranteed. ► Carry out regular visual checks to detect wear and tear and dirt. ► Immediately replace damaged parts. ► Immediately remove dirt without leaving any residues. ► Immediately replace parts with stubborn dirt. Inappropriate handling when plugging or disconnecting may damage the connectors. The functional safety of the connectors is no...

Open the catalog to page 7
Manual, Connectors to UIC 558 - 8

4.2 Design Connectors in the UIC 558 series are 13 or 18-pole connectors to loop through different control signals between railway vehicles. The connectors are in compliance with UIC 558. They connect lines used for: X remote control of lights X remote control of doors X public address system in passenger coaches and traction vehicle X transmission of binary data Connectors in the UIC 558 series consist of the following components: X Connector cable, single ended, in the desired length with cable plugs, single-sided assembly, or connector cable, double ended, with two cable plugs,...

Open the catalog to page 8
Manual, Connectors to UIC 558 - 9

4.3 Survey of the Components (Preferred Types)Connector cable with plug (single ended) No. of contacts Ordering code Connector cable with cable harness and plug, completely assembled cable set in required length, 13-pole, pin contacts (13-pole plug with less equipped 18 pole cable) Connector cable with plug, completely assembled cable set in required length 18-pole, pin contacts Ordering code 13-pole version: UIC VK 13P E0 Lxxxx 11 18-pole version: UIC VK 18P ER Lxxxx 11 Connector cable with 2 plugs, completely assembled cable set in required length, available in 13-pole and 18-pole...

Open the catalog to page 9
Manual, Connectors to UIC 558 - 10

18-pole coupling receptacle with socket insert and connector cable No. of contacts 18-pole socket insert with connector cable: UIC DL 18S 00 Lxxxx 1) + Empty receptacle: UIC LD 180 CR (RAL 7035, light grey, red colour markings) Connector cable with socket insert, completely assembled cable set in required length, 18-pole, socket contacts + empty receptacle 18-pole coupling receptacle with replacement insert, crimp adapter and connector cable No. of contacts Crimp adapter Replacement insert Empty receptacle Crimp adapter with connector cable, completely assembled cable set in required...

Open the catalog to page 10
Manual, Connectors to UIC 558 - 11

Coupling receptacle, dummy receptacle, empty receptacle No. of contacts Ordering code Coupling receptacle - 13-pole: UIC KD 13S C0 (RAL 7035, light grey) - 18-pole: UIC KD 18S CR Coupling receptacle, dummy receptacle (RAL 7035, light grey, red colour markings): (RAL 7035, light grey, blue colour markings): Dummy receptacle - 13-pole: UIC BD 130 C0 (RAL 7035, light grey) (RAL 7035, light grey, red colour markings): (RAL 7035, light grey, blue colour markings) Earthing bolt M6, only special design F4 - Coupling receptacle with socket insert and crimp contacts (all socket contacts are included...

Open the catalog to page 11
Manual, Connectors to UIC 558 - 12

5. Installation DANGER The connectors contain components that carry voltage. Risk of electric shock! Always observe the following safety regulations before beginning any work on electrical constructions: X Disconnect X Ensure that it is not possible to reconnect unintentionally X Clearly mark your work area X Make sure that there is no voltage present X Earth and short circuit the installation X Insulate or cover adjacent energized parts X Only an electrically skilled person may determine if there is no voltage present NOTICE During installation, ensure that dirt caused by surrounding...

Open the catalog to page 12

All Schaltbau GmbH catalogs and technical brochures

  1. Flyer C320

    8 Pages

  2. UIC-IT Series

    12 Pages

  3. Brochure

    8 Pages

  4. Connectors

    7 Pages

  5. LV Series

    12 Pages

  6. SB Series

    8 Pages

  7. GA Series

    10 Pages

  8. G, GM series

    44 Pages

  9. Brochure en

    6 Pages

  10. S880 Series

    12 Pages