Catalog excerpts
Automation / Mini Resolution: Supply Voltage: Output Voltage: Output Current: Frequency Response: Output Format: Phase Sense: Incremental 1 to 7500 ppr (pulses per revolution) 4,5 Vdc min. to 30 Vdc max. (35 mA max. - no load) Low: 500 mV max. at 10 mA High: (Vin – 0,6) at -10 mA (Vin – 1,3) at -25 mA 25 mA max. load per output channel 200 kHz max. Brass Electroplated Steel Aluminum (flat cable option) Hollow Shaft: Brass Encoder: ~ 35 gr (1,23 oz) Cable: 50 gr / meter (1,76 oz / meter) > 1,9 x 1010 revolutions at rated load Shaft Speed: Starting Torque: Mass Moment of Inertia: Shaft Loads: Two channel (A, B) quadrature with Index (Z) and optional complementary (A-, B-, Z-) outputs A leads B clockwise (CW) from the mounting end of the encoder Noise Immunity: Bearing Life: Gated with Channels A and B high Electrical Protection: Mechanical Specifications Hollow Bore: Electrical Specifications Hollow Shaft Encoder - ASIC Push-pull and Differential OL7272 Push-pull and Differential Line Driver 26C31 Differential Line Driver 5V output (with 5V input) Reverse polarity and output short circuit protected Tested to EN61000-6-2 : 2005 (industrial environments) Electromagnetic compatibility (EMC) and EN 61000-6-3 : 2007 (residential, commercial, and lightindustrial environments) for Electromagnetic compatibility (EMC) Environmental Specifications Operating Temp.: Storage Temp.: Enclosure Rating: IP 64 / Nema 4 (approx.) IP 50 / Nema 5 (approx.) - flat cable Connection Options Cable: 8 leads (0,05 mm2, 30 AWG) - Differential 5 leads (0,14 mm2, 26 AWG) - Standard twisted pairs; shielded Flat Cable: 10 lead flat cable with IDC connector ** = It is recommended user, not to combine max. values for all 3 parameters
Open the catalog to page 1Type SCH24 Output waveform Disk Resolutions (pulses per revolution) Channel tolerance Phase difference tolerance Z channel tolerance Other options on request Pulses per revolution, min. 1 – max. 7.500 Mechanical Dimensions Tolerances according to ISO 2768 f
Open the catalog to page 2Industrial Encoders Spring coupling Flat Ribbon Cable with IDC connector
Open the catalog to page 3Type SCH24 Output Terminations Standard Cable Standard Output Channel A AB BZ ZVsup GND Differential Output Wire Color Green NC Yellow NC Gray NC Brown White Flat Cable w/ IDC Connector Differential Output * Position Pink Gray Green Yellow White Brown Red Blue * Hewlett Packard (HP) compatible Differential Output IP 50 rating CE mark not available 0,5 m, 1 m, or 2 m cable length only Standard Output mm (inches) mm (inches) mm (inches)
Open the catalog to page 4Type SCH24 Ordering Code Hollow Shaft Length Cable Length Cable Connector Takeout Spring Coupling IP 50 50* IP 64 64 * = Only Flat Cable Standard Standard – Open Collector NPN Standard – Open Collector PNP Differential 26C31 Line Driver Standard Cable Standard is 1 meter Specify length Flat Cable w/ IDC 0,5 meter Standard - with built-in TSM ** Side (radial) Back (axial) Flat cable w/ IDC connector Standard Cable Flat Cable IDC on flat * = Only IP 50 cable* *= Only IP 50 For Scancon Motor Flanges 2 points p/n 80147242 S1 2 points p/n 80139908 S2 Other options on request: Please contact...
Open the catalog to page 5All Scancon catalogs and technical brochures
-
2R58
5 Pages
-
scancon encoders atex
8 Pages
-
overview scancon encoders
2 Pages
-
automated machinery brochure
5 Pages
-
eCODE 2048 Series
2 Pages
-
Ex Junction Box
5 Pages
-
SCH94FO
5 Pages
-
SCH108BEX/ Absolute
4 Pages
-
SCH32F
5 Pages
-
SCH32B
5 Pages
-
2RMHF
5 Pages
-
2SUN
3 Pages
-
SCA-BM
4 Pages
-
SCA41
5 Pages
-
SCA40
5 Pages
-
SCA38
5 Pages
-
SCA36,5
5 Pages
-
SCA34
5 Pages
-
SCA30
5 Pages
-
SCA28
5 Pages
-
SCA24-IP65
4 Pages
-
SCA24
5 Pages
-
SCH16F
5 Pages
-
Type SCH16G
4 Pages
-
Type SCA787
4 Pages
-
Type SCA18
4 Pages
-
Type SCA16
5 Pages
-
Type SCH68B
5 Pages
-
Type SCA50
5 Pages
-
DIN Rail Junction Box
4 Pages
-
Type 2RMHD
4 Pages
-
Transient Suppression Module
3 Pages
-
eCode, intelligent encoders
2 Pages
-
Jog Handle for CNC Panels
2 Pages