Catalogs >
Scancon >
SCA41

SCA41
5Pages

Catalog excerpts

Automation / Mini Resolution: Supply Voltage: Output Voltage: Output Current: Frequency Response: Output Format: Phase Sense: Incremental 1 to 7500 ppr (pulses per revolution) 4,5 Vdc min. to 30 Vdc max. (35 mA max. - no load) Low: 500 mV max. at 10 mA High: (Vin – 0,6) at -10 mA (Vin – 1,3) at -25 mA 25 mA max. load per output channel 200 kHz max. Housing: Aluminum Cap: Electroplated Steel Aluminum (flat cable option) Shaft: Stainless Steel Encoder: ~ 50 gr (1,76 oz) Cable: 50 gr / meter (1,76 oz / meter) > 1,9 x 1010 revolutions at rated load Shaft Speed: Starting Torque: Mass Moment of Inertia: Shaft Loads: Two channel (A, B) quadrature with Index (Z) and optional complementary (A-, B-, Z-) outputs A leads B clockwise (CW) from the mounting end of the encoder Noise Immunity: Bearing Life: Gated with Channels A and B high Electrical Protection: Mechanical Specifications Electrical Specifications Shaft Encoder - ASIC Push pull and Differential OL7272 Push-pull and Differential Line Driver 26C31 Differential Line Driver 5V output (with 5V input) Reverse polarity and output short circuit protected Tested to EN61000-6-2 : 2005 (industrial environments) Electromagnetic compatibility (EMC) and EN 61000-6-3 : 2007 (residential, commercial, and lightindustrial environments) for Electromagnetic compatibility (EMC) Environmental Specifications Operating Temp.: Storage Temp.: Enclosure Rating: IP 64 / Nema 4 (approx.) IP 50 / Nema 5 (approx.) - flat cable Connection Options Cable: 8 leads (0,05 mm2, 30 AWG) - Differential 5 leads (0,14 mm2, 26 AWG) - Standard twisted pairs; shielded Flat Cable: 10 lead flat cable with IDC connector = It is recommended, not to combine max. Value for all 3 parameters

Open the catalog to page 1

Type SCA41 Output waveform Disk Resolutions (pulses per revolution) Channel tolerance Phase difference tolerance Z channel tolerance Other options on request Pulses per revolution, min. 1 – max. 7.500 Mechanical Dimensions

Open the catalog to page 2

Industrial Encoders Flat Ribbon Cable with IDC connector

Open the catalog to page 3

Type SCA41 Output Terminations Flat Cable w/ IDC Connector Standard Cable Standard Output Channel A AB BZ ZVsup GND Differential Output Differential Output * Wire Color Green NC Yellow NC Gray NC Brown White Pink Gray Green Yellow White Brown Red Blue * Hewlett Packard (HP) compatible IP 50 rating CE mark not available 0,5 m, 1 m, or 2 m cable length only Standard Output mm (inches) mm (inches) mm (inches) Differential Output

Open the catalog to page 4

Type SCA41 Ordering Code ** Designed specifically for Wind Power applications. See SCA24 COC under Industries – Wind Power – SCA24 for additional conformity standards testing. TSM = Transient Suppression Module Available only as Standard output Shaft Length Cable Length Cable Takeout See table IP 64 IP 50 Standard Standard – Open Collector NPN Standard – Open Collector PNP Differential 26C31 Line Driver 5V only OL 7272 Line Driver Standard - with built-in TSM ** Standard Cable Standard is 1 meter Specify length Flat Cable w/ IDC 0,5 meter 1,0 meter 2,0 meters * = Only Flat Cable 6.0 mm 6.0...

Open the catalog to page 5

SCA41 5Pages

Catalog excerpts

All Scancon catalogs and technical brochures

SCA41
5Pages