Catalogs >
Scancon >
SCA38

SCA38
5Pages

Catalog excerpts

Automation / Mini Supply Voltage: Output Voltage: Output Current: Frequency Response: Output Format: Phase Sense: 1 to 7500 ppr (pulses per revolution) 4,5 Vdc min. to 30 Vdc max. (35 mA max. - no load) Low: 500 mV max. at 10 mA High: (Vin – 0,6) at -10 mA (Vin – 1,3) at -25 mA 25mA max. load per output channel 200 kHz max. Housing: Aluminum Cap: Electroplated Steel Shaft: Stainless Steel Encoder: ~ 40 gr (1,41 oz) Cable: 50 gr / meter (1,76 oz / meter) Bearing Life: > 1,9 x 1010 revolutions at rated load Shaft Speed: Starting Torque: Mass Moment of Inertia: Shaft Loads: Axial: Radial: Two channel (A, B) quadrature with Index (Z) and optional complementary (A-, B-, Z-) outputs A leads B clockwise (CW) from the mounting end of the encoder Noise Immunity: Mechanical Specifications Gated with Channels A and B high Electrical Protection: Electrical Specifications Shaft Encoder - ASIC Push pull and Differential OL7272 Push-pull and Differential Line Driver 26C31 Differential Line Driver 5V output (with 5V input) Reverse polarity and output short circuit protected Tested to EN61000-6-2 : 2005 (industrial environments) Electromagnetic compatibility (EMC) and EN 61000-6-3 : 2007 (residential, commercial, and lightindustrial environments) for Electromagnetic compatibility (EMC) Environmental Specifications Operating Temp.: Storage Temp.: Enclosure Rating: IP 50 / Nema 5 (approx.) - Flat IP 65 / Nema 4 (approx.) - option Connection Options Cable: 8 leads (0,05 mm2, 30 AWG) - Differential 5 leads (0,14 mm2, 26 AWG) - Standard twisted pairs; shielded Flat Cable: 10 lead flat cable with IDC connector = It is recommended, not to combine max. Value for all 3 parameters

Open the catalog to page 1

Type SCA38 Output waveform Disk Resolutions (pulses per revolution) Channel tolerance Phase difference tolerance Z channel tolerance Other options on request Pulses per revolution, min. 1 – max. 7.500 Mechanical Dimensions

Open the catalog to page 2

Flat Ribbon Cable with IDC connector

Open the catalog to page 3

Type SCA38 Output Terminations Standard Cable Standard Output Channel A AB BZ ZVsup GND Flat Cable w/ IDC Connector Differential Output Wire Color Green NC Yellow NC Gray NC Brown White Differential Output * Position Pink Gray Green Yellow White Brown Red Blue * Hewlett Packard (HP) compatible Differential Output IP 50 rating CE mark not available 0,5 m, 1 m, or 2 m cable length only Standard Output mm (inches) mm (inches) mm (inches)

Open the catalog to page 4

Type SCA38 Ordering Code Shaft Length Cable Length Cable Takeout See table IP 50 IP 65 Standard Standard – Open Collector NPN Standard – Open Collector PNP Standard Cable Standard is 1 meter Specify length OL 7272 Line Driver Standard - with built-in TSM ** Flat Cable w/ IDC* 0,5 meter 1,0 meter 2,0 meters Side (radial) Back (axial) Flat cable w/ IDC connector * = Only Flat Cable ** Designed specifically for Wind Power applications. See SCA24 COC under Industries – Wind Power – SCA24 for additional conformity standards testing. Other options on request: Please contact Scancon A/S TSM =...

Open the catalog to page 5

SCA38 5Pages

Catalog excerpts

All Scancon catalogs and technical brochures

SCA38
5Pages