*mydirectindustry

2R58

Product catalog summary

Mechanical Specifications:
The encoder housing and cap are made of aluminum, while the shaft is stainless steel. The encoder weighs approximately 190 grams, with an additional 60 grams per meter for the cable. It supports a shaft speed of up to 3,000 rpm and has a bearing life exceeding 1.9 x 10¹⁰ revolutions at rated load. The starting torque is less than 0.02 Nm at 25°C, and it can handle axial and radial shaft loads of up to 50 N.

Electrical Specifications:
The encoder is incremental with a resolution range from 1 to 12,500 pulses per revolution (ppr). It operates on a supply voltage between 4.5 Vdc and 30 Vdc, with a maximum output current of 30 mA per channel. The frequency response is up to 300 kHz. It features two-channel quadrature output with an index and optional complementary outputs. The encoder is protected against reverse polarity and output short circuits, and it complies with EMC standards EN61000-6-2:2005 and EN61000-6-3:2007.

Environmental Specifications:
The operating and storage temperature range is -40°C to +85°C. It can withstand shocks of 100 G for 11 ms and vibrations from 10-2000 Hz at 10 G. The encoder is rated IP 67, indicating high resistance to dust and water.

Connection Options:
The encoder offers various connection options, including 5-pin and 8-pin M12 connectors, and 9-pin and 12-pin M23 connectors. The standard cable has 8 leads, is shielded, and consists of twisted pairs.

Output Terminations:
The document provides detailed wiring information for different connector types, specifying wire colors and pin assignments for standard and differential outputs.

Ordering Code:
The ordering code for the encoder includes specifications for pulses per revolution, output type, shaft diameter and length, IP rating, cable length, and connector type. Custom options are available upon request.

Catalog excerpts

Industrial Encoders Automation / Standard Type 2R58 • Shaft Encoder - 0 58 mm • Shaft: 0 6 in to 0 10 mm • Resolution up to 12.500 ppr • Terminal Shut down at 155 °C • Standard IP 67 Electrical Specifications Scancon Huginsvej 8 3400 Hillernd Denmark

Open the catalog to page 1

Industrial Encoders Type 2R58 Output waveform Disk Resolutions (Pulses per revolution) Channel tolerance Phase difference tolerance Z channel tolerance Other options on request Pulses per revolution, min. 1 - max. 12.500 Mechanical Dimensions Standard Cable Gland Side (S) or Back (B) p. 2 Rev. 2.0 27. April - 2015 Scancon Huginsvej 8 3400 Hillerad Denmark

Open the catalog to page 2

Industrial Encoders Type 2R58 Adaptor for the connector Rev. 2.0 27. April - 2015 Scancon Huginsvej 8 3400 Hillernd Denmark

Open the catalog to page 3

Industrial Encoders Type 2R58 Output Terminations Channel A A -B B -Z Z -Vsup GND Standard Cable Standard Differential Output Output Wire Color Pink Gray* Green Yellow* White Brown* Red Blue Pink Gray Green Yellow White Brown Red Blue GND = Circuit Ground * Internally connected as GND Shield GND = Circuit Ground Shield = Case Ground Rev. 2.0 27. April - 2015 Scancon Huginsvej 8 3400 Hillered Denmark

Open the catalog to page 4

Industrial Encoders Type 2R58 Ordering Code Example: 2R58 - 1024 - D - 6 - 12 - 67 - 01 - S - 00 Pulses per Output Revolution I See table Shaft Shaft Dia. Length IP Cable Takeout Connector Standard - Open Collector NPN NON Standard - Open Collector PNP NOP 26C31 Line Driver 5 V / 5 V only L Other options on request: Please contact Scancon A/S Rev. 2.0 27. April - 2015 Scancon Huginsvej 8 3400 Hillerod Denmark

Open the catalog to page 5

All Scancon catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list