ACDC Fan ■ Features High Airflow and High Static Pressure This fan delivers a maximum airflow of 8.2 m3/min and maximum static pressure of 167 Pa. Low Noise and Low Power Consumption This fan operate with a noise level of 58 dB(A) and power consumption of 22 W. Also, the PWM control function enables the control of fan speed, contributing to lowering noise and improving energy efficiency of devices. Wide Operating Voltage Range This fan has an input voltage range of 100 to 240 VAC, supporting both 100 and 200 VAC systems. Water and Dust Protection This fan achieves excellent IP56* water and dust protection, maintaining stable operation in harsh environments. *The degree of protection (IP code) is defined by IEC 60529 (International Electrotechnical Commission). The protection rating applies only to electrical components (motor coils and electronic components) in our fans. The mechanical components other than the electrical components are not subject to protection. 160 × 160 × 51 mm ■ Specifications Lead wire model The models listed below have pulse sensors with PWM control function. Model no. PWM Rated voltage Operating Frequency duty cycle* Rated current Rated input Rated speed voltage range [V] [Hz] [A] [W] [min-1] [V] [%] * PWM frequency is 25 kHz. Models without ratings for 0% PWM duty cycle have zero speed at 0%. When control terminal is open, speed is the same as at 0% duty cycle. The models listed below have no sensors. Model no. Operating voltage range [V] Terminal model The models listed below have pulse sensors with PWM control function. Model no. PWM Rated voltage Operating Frequency Rated current Rated input Rated speed duty cycle* voltage range [V] [Hz] [A] [W] [min-1] [V] [%] * PWM frequency is 25 kHz. Models without ratings for 0% PWM duty cycle have zero speed at 0%. When control terminal is open, speed is the same as at 0% duty cycle. The models listed below have no sensors. Model no. Operating voltage range [V] Models with the following sensor specifications are also available as options: ■ Common Specifications ・・・・・・・・・・・・・・ □ Material ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ Frame: Aluminum (Black coating), Impeller: Plastic (Flammability: UL 94V-0) ・・・・・・・・・・・・ □ Expected life ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ Refer to specifications (L10 life: 90% survival rate for continuous operation in indoor free air at 60°C, rated voltage) Expected life at 40°C is for reference only. ・・・・・・ □ Motor protection function・ ・ ・ ・ ・ ・ Locked rotor burnout protection ・・・・・・・・・ □ Dielectric strength ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 50/60 Hz, 1500 VAC, for 1 minute (Lead wire model: between lead wire conductors and frame, Terminal model: between terminal and frame) ・・・・・・・・ □ Insulation resistance ・ ・ ・ ・ ・ ・ ・ ・ ・ 10 MΩ min. at 500 VDC (Lead wire model: between lead wire conductors and frame, Terminal model: between terminal and frame) ・・・・・ □ Sound pressure level (SPL) ・ ・ ・ ・ ・ A-weighted sound pressure level (SPL) at 1 m away from the air inlet. ・・・・・・・ □ Operating temperature ・ ・ ・ ・ ・ ・ ・ Refer to specifications (Non-condensing) ・・・・・・・・ □ Storage temperature ・ ・ ・ ・ ・ ・ ・ ・ ・

■ Airflow - Static Pressure Characteristics (inch H2O) Static pressure Static pressure ■ PWM Duty - Speed Characteristics Example Input voltage: 100 VAC 50/60 Hz 240 VAC 50/60 Hz PWM frequency: 25 kHz

160 × 160 × 51 mm ■ PWM Input Signal Example Input signal waveform VIH = 4.75 to 5.25 V　VIL = 0 to 0.4 V VIL When the PWM control terminal is open, the fan speed is the same as the speed at 0% PWM duty cycle. A TTL input can be used for the PWM input signal. ■ Example of Connection Schematic Inside of fan Isource Isink PWM input signal ■ Specifications for Pulse Sensors Output circuit: Open collector Inside of fan Pull-up voltage Photocoupler Pull-up resistor Sensor output Output waveform (Need pull-up resistor) In case of steady running (One revolution) T0 T1 VOH VOL 0V PWM duty cycle (%) = T...

■ Dimensions (unit: mm) (With pulse sensor with PWM control function) Lead wire model Terminal model Power lead wire 6±0.4 AWG 22 UL 11347 Other lead wire AWG 24 UL 1430 Rotating direction Airflow direction Rotating direction A Connector contact Pin arrangement Connector (Model no.: TE Connectivity: 1-172160-9) Pin No. Function Input 1 ■ Reference Dimensions of Mounting Holes and Vent Opening (unit: mm) Inlet side, Outlet side 157 ■ Options Finger guards Terminal model wiring harness ●Please read the "Safety Precautions" on our website before using the product. ●The products shown in this catalog...